Jan 26

This article teaches you how to use D-Link DSL-2320B setting to service provider.

Step 1: Plug the power adapter into the D-Link DSL-2320B and turn on the power by pressing the button on the back of the unit. When the modem has fully boot up, you should only see the power and DSL LEDS lit solid indicating no activity.

Step 2: Plug one end of the USB cable into the modem and the other end into one of your PC’s USB ports. The found new hardware wizard should detect a new network device.

It should then prompt you to install the drivers for the device.

How to connect my D-Link DSL-2320B to my service provider using the USB cable?

Step 3: At this time insert the CD that came with the modem. It should automatically install the correct driver without any interaction.

The driver should now be installed and ready for use. Click Finish.

How to connect my D-Link DSL-2320B to my service provider using the USB cable?

Step 4: Now open a command prompt and type ipconfig. Verify that the PC has received an IP address of 192.168.1.x. Now type, ping 192.168.1.1 to verify that the PC can talk to the modem. If you get replies you are now ready to log into the modem and configure the connection with your ISP.

Step 5: Log into the modem by typing the default IP address of the modem into the address bar, http://192.168.1.1 and hit Enter. This will take you to the login prompt.

How to connect my D-Link DSL-2320B to my service provider using the USB cable?

Step 6: Type admin for the username and admin for the password and hit the OK button. This will take you to the Home page of the routers Interface.

Step 7: On the home page, check the box that says DSL-Auto-Connect, and click the Next button.

The modem will search for the appropriate virtual connection that coinsides with your DSL provider’s service. When it is done it will tell you which PVC parameters can be used. Click the OK button.

Step 8: This will bring you to the PPP Username and Password screen. On this page you will input the username and the password used for you internet connection, that is provided to you by your ISP for your DSL connection. Then click Next.

How to connect my D-Link DSL-2320B to my service provider using the USB cable?

Step 9: The setup summary page will display the configuration settings that you have set. Now click on the Save and Reboot button.

How to connect my D-Link DSL-2320B to my service provider using the USB cable?

When you reboot, a screen will display showing your progress.

How to connect my D-Link DSL-2320B to my service provider using the USB cable?

When the progress is finished, a prompt will appear telling you the modem has rebooted and is up and running.

Step10: Now to verify connectivity, open a command prompt and type ipconfig and hit Enter.
You should see a valid bridged WAN IP address that may resemble the one below.

How to connect my D-Link DSL-2320B to my service provider using the USB cable?

Tags: ,

Jan 26

Store-and-Forward:

Store-and-Forward switching will wait until the entire frame has arrived prior to forwarding it. This method stores the entire frame in memory. Once the frame is in memory, the switch checks the destination address, source address, and the CRC. If no errors are present, the frame is forwarded to the appropriate port. This process ensures that the destination network is not affected by corrupted or truncated frames.

Cut-Through:

Cut-Through switching will begin forwarding the frame as soon as the destination address is identified. The difference between this and Store-and-Forward is that Store-and-Forward receives the whole frame before forwarding. Since frame errors cannot be detected by reading only the destination address, Cut-Through may impact network performance by forwarding corrupted or truncated frames. These bad frames can create broadcast storms wherein several devices on the network respond to the corrupted frames simultaneously.

Tags: ,

Jan 26

DWL-2100AP Introduction:

D-Link AirPlus Xtreme GTM series of high-speed devices now capable of delivering transfer rates up to 15x faster than the standard 802.11b with the new D-Link 108G. With the new AirPlus Xtreme G DWL-2100AP Wireless Access Point, D-Link sets a new standard for wireless access points.

The DWL-2100AP Wireless Access Point also supports SNMP v.3 for better network management with the provided Wireless AP Manager software that manages network configuration and firmware upgrades. For Enterprise networks, the DWL-2100AP supports network administration and real-time network traffic monitoring via D-Link’s D-View Network Management software.

The DWL-2100AP features WDS (Wireless Distribution System) that can be configured to perform in any one of five modes: a Wireless Access Point, a Point-to-Point (PtP) bridge with another DWL-2100AP, a Point-to-Multipoint (PtMP) bridge, a Repeater for range extension, or as a Wireless Client. The WDS feature makes the DWL-2100AP an ideal solution for quickly creating and extending a wireless local area network (WLAN) in offices or other workplaces, or even at hotspots.

DWL-2100AP Firmware Download:

Now the DWL-2100AP Firmware Version:2.13

Date:2/26/2009

Revision Info:
¤ Remove the default setting user name “user”.
¤ The password field should have current password

Download Now : ftp://ftp.dlink.com/Wireless/dwl2100AP/Firmware/dwl2100AP_firmware_213.zip

Tags: ,

Jan 26

Step 1: Attach the USB hub to you PC with the USB cable provided.

DUB-1210a

Step 2: Open the Wireless USB Control Center software

DUB-1210b

Step 3: Select the Administration tab

DUB-1210c

Step 4: Enter Admin password in the Enter New Adminstration password field and enter password again in the Confirm Adminstration password field to confirm and click Set. User Passwords can also be set here.

When attempting to access the Administration screen you will be prompted to enter the administrator password:

DUB-1210d

Tags: ,

Jan 26

This article teach you how to config a DWL-3140AP with a DES-1228P.

Step 1: Upgrade the firmware on the DES-1228P to the latest version.

Step 2: Download and install the latest Smart WLAN Manager software.

Step 3: Connect the DWL-3140AP into the DES-1228P (make sure the power and LAN LED turn on).

Step 4: Run the Smart WLAN Manager software. Click on the Discover Wizard button on the top left corner if the software doesn’t detect the DWL-3140AP right away.

How to configure a DWL-3140AP with a DES-1228P?

Step 5: Enter the DHCP IP pool range and then click on Add.

How to configure a DWL-3140AP with a DES-1228P?

Step 6: Select the discovered DWL-3140 and click on Save.

Step 7: Right click on the access point you wish to setup and select Configuration. This is where you can configure the basic settings such as the IP address and SSID.

How to configure a DWL-3140AP with a DES-1228P?

Tags: ,



 
Prev 1 2 3 4 5 6 7 8 9 Next
css.php