Aug 14

DDNS(Dynamic DNS) will allow you to access your public IP address by domain name. The DDNS feature updates your public IP address with the DDNS provider each time it renews.

Step 1 Register with one of the following DDNS providers. If you already have an account with a DDNS provider listed below, skip to Step 2.

  • ChangeIP.com
  • DynDNS.org
  • EuroDynDNS.org
  • hn.org
  • no-ip.com
  • ods.org
  • ovh.com
  • regfish.com
  • tzo.com
  • Step 2: Open a web browser and type the IP address of the D-Link gaming router in the address bar (default is 192.168.0.1). Press Enter.

    Step 3: The default password is blank (nothing). Click Log In.

    Step 4 Click Tools at the top and then click Dynamic DNS on the left side.

    gaming-router-ddns

    Step 5: Select the Dynamic DNS Enabled checkbox and configure the following:

    • Server Address – Select the DDNS provider that you registered with
    • Host Name – Enter the domain name that you registered (i.e. mydomain.provider.org)
    • Username or Key – Enter the username for your DDNS account
    • Password or Key – Enter the password for your DDNS account
    • Verify Password or Key – Confirm the password for your DDNS account
    • Timeout – Enter the timeout (in hours) in which the gaming router will update your DDNS account if your IP address has not changed

    Step 6: Click Save Settings at the top to apply the DDNS settings.

    Tags: , , ,

    Aug 14

    This FAQ is for the D-Link DCS-2000, DCS-2100, DCS-2100G, DCS-2100+, DCS-3220, DCS-3220G, DCS-3420, DCS-5300, DCS-5300G, DCS-5300W, DCS-6620, DCS-6620G cameras.

    Dynamic DNS (DDNS) allows remote administration of the camera using a domain name in situations where a static IP address is not available. Each time a new dynamic IP address is pulled, the camera updates the IP address with the DDNS service provider.

    Step 1: Register with one of the following DDNS providers:

    DynDNS.org
    TZO.com
    dhs.org
    Write down the URL and login information you obtained after registering with one of the above DDNS providers.

    Step 2: Log into the web-based configuration of the camera.

    Step 3: Click Configuration to the left.

    Step 4: Click the Advanced tab and then click DDNS&UPnP to the left.

    camera-ddns

    Step 5: Click the Enable DDNS checkbox.

    Step 6: Select the provider that you registered with from the drop-down list next to Provider.

    Step 7: Using the information you obtained in Step 1 enter the domain name that you created (i.e. mycamera.dyndns.org) in the field by Host Name. Enter your login information for the account in the Username/Email and Password/Key fields.

    Step 8: Click Apply and then Continue to save the new settings.

    Tags: , ,

    Aug 14

    Dynamic DNS (Domain Name Service) is a method of keeping a domain name linked to a changing (dynamic) IP address. With most Cable and DSL connections, you are assigned a dynamic IP address and that address is used only for the duration of that specific connection. To properly configure the DDNS feature follow the steps below:

    Step 1: Open a web browser and type the IP address of the DI-LB604 into the address bar (default is 192.168.0.1).

    Step 2: The default username is admin (all lower case) and the default password is blank (nothing). Click on OK.

    Step 3: Click on the Tools tab at the top and then click on DDNS on the lefthand side.

    dlink-ddns01

    Step 4: For service, select your DDNS service provider from the drop-down and configure the following:

    • Server Name – The name of the DDNS server.
    • User Name – Enter the username for your DDNS account.
    • Password – The password for your DDNS account.
    • Verify Password – Re-enter the password to prevent any typing errors.
    • Domain Name – The complete hostname to be updated.

    Additional Settings:

    • Enable Wildcard: If enabled, all subdomains of your domain name map to your current IP address. If disabled, no subdomains of your domain name have an IP address.
    • Enable Backup MX: If enabled, all subdomains of your domain name map to your current IP address. If disabled, no subdomains of your domain name have an IP address.
    • Mail Exchanger: Define mail exchanger for the domain name. If omitted, the mail exchanger will be set to the domain name.

    WAN Port Binding: If bound on the WAN port, the domain name will be mapped to the IP address of the WAN port.

    Step 5: Click on Apply to save your settings.

    Tags: , ,

    Aug 13

    You must open ports on your router to allow incoming traffic while using eMule.

    eMule uses three ports*:

  • 4662 (TCP)
  • 4672 (UDP)
  • 4711 (TCP)
  • * To prevent getting a low ID (Firewalled), open additional TCP ports between 4661 and 4665. Also, limit the number of connections in the eMule software. You may need to change the TCP Clientport to something other than 4662.

    emule-dlink

    1.For the DI-5xx, DI-6xx, DI-704P (revC), DI-704UP, DI-754, DI-764, DI-774, DI-784, DI-804HV, DI-808HV, and DI-824VUP:

    Step 1: Open your web browser and enter the IP address of your router (192.168.0.1). Enter username (admin) and your password (leave blank).

    Step 2: Click on Advanced and then click Virtual Server.

    Step 3: Create a new entry:

  • Click Enabled.
  • Enter a name (emule1).
  • Private IP – Enter the IP address of the computer you are running eMule from.
  • Select TCP for Protocol Type
  • Enter 4662 for both Private Port and Public Port
  • Click Always or set a schedule.
  • Step 4: Click Apply and then Continue.

    emule-dlink2

    Step 5: Repeat steps 3 and 4 but name it emule2, select UDP for Protocol Type, and enter 4672 for both Private Port and Public Port.

    Step 6: Repeat steps 3 and 4 but name it emule3, select TCP for Protocol Type, and enter 4711 for both Private Port and Public Port.

    Note: If the screenshots look different (DI-604), then you have the European version of your router which D-Link USA does not support.

    2.For the DI-704P (revA), DI-704, DI-707, DI-711, DI-713, and DI-713P:

    Step 1 Open your web browser and enter the IP address of the router (192.168.0.1). Enter user name (admin) and your password (blank by default). If there is only 1 box, enter admin.

    Step 2 Click on Advanced at the bottom and then click Virtual Server.

    Step 3 Create a new entry:

    • Enter 4661-4665 in the box under Service Ports.
    • Enter the IP address of the computer you want to run eMule from.
    • Check the box under Enable.
    • In the next box down, enter 4672 under Service Ports.
    • Enter the IP address of the computer you want to run eMule from.
    • Check the box under Enable.
    • In the next box down, enter 4711 under Service Ports.
    • Enter the IP address of the computer you want to run eMule from.
    • Check the box under Enable.

    emule-dlink3

    Step 4: Click Save and the click Reboot.

    NOTE: If you can only enter a single port (not a range) and/or are limited to 10 entries, upgrade your firmware to the latest version at support.dlink.com/downloads.

    Tags: , , , , ,

    Aug 13

    This FAQ is for the DI-514, DI-524, DI-604, DI-614+, DI-624, DI-624S, DI-754, DI-764, DI-774, and DI-784 routers.

    Nortel Contivity will work with the your D-Link router, however its functionality depends on the authentication type (AH will not work), NAT compatibilty mode, and disabling keep alives on the server. Contact your Network Administrator to find out how your VPN is configured.

    Step 1: Verify that you are using the latest version of firmware on your router.

    Step 2: Login to the Web Management for your router by entering its IP address (192.168.0.1) in your web browser. The default username is admin, and the password is blank.

    Step 3: Click the Advanced Tab to access the Virtual Server Settings. There is a list of pre-defined Virtual Server Rules towards the bottom of the page. Find the IPSec Rule. Click the pen and paper icon to edit its settings. Enable the rule, enter the IP address of the computer attempting to connect to the VPN in the Private IP field, then Apply the changes.

    dlink-nortel2

    Step 4: Create a new Virtual Server entry. Name the Virtual Server, “NortelVPN“. Enter the IP address of the computer attempting to connect to the VPN in the Private IP field. For the Protocol Type, select Both. Enter 9550 for both the Public and Private Ports. Set the Schedule to always, then Apply the settings.

    dlink-nortel1

    Step 5: Access the Tools Page, then click the Misc button. Disable IPSec Pass-through, then click Apply.

    dlink-nortel3

    If the VPN Server is properly configured to work with clients behind NAT routers you should be able to connect to the VPN.

    Tags: , , ,



     
    Prev 1 2 3 4 5 6 7 8 9 10 ... 14 15 16 Next
    css.php