Apr 27

Step 1: Open your web browser such as Internet Explorer and enter the IP address of the D-Link DWL-7100AP access point in the Address bar and press Enter. The default IP address is 192.168.0.50.

Step 2: Enter your user name (admin) and your password (leave blank by default). Click OK.

Step 3: Click the Advanced tab and then click Grouping on the left side.

Step 4: Next to Load Balance, select Enabled from the drop-down box.

When you Enable Load Balance you allow several D-Link DWL-7100AP/DWL-7000AP access points to balance wireless network traffic and wireless clients among the access points with the same SSID. All the APs that share Load Balancing must have the same SSID. Assign each Access Point a different non-overlapping channel (e.g., 1, 6, 11).

Step 5: Next to Link Integrate, select Enable from the drop-down box.

When Link Integrate is Enabled, the wireless segment associated with the AP will be disconnected whenever the connection between the AP and the LAN is dropped.

Step 6: Click Apply and then click Continue to save your settings.

Tags: ,

Apr 27

To change or obtain an IP address automatically for the D-Link DWL-7100AP follow the steps below:

Step 1: Open your web browser and type the IP address of the access point in the address bar. The default IP address is 192.168.0.50. At the login, enter your username (admin) and password (default password is blank).

Step 2: Click on the Home tab and then click LAN.

Step 3: Select Dynamic (DHCP) from the drop-down list if you want the access point to receive an IP address automatically from a DHCP server or router, otherwise change the IP address manually (static).

We strongly suggest using a static IP address. The IP address is not used for networking, only for configuration. Make sure the IP address is within the same IP range as your network.

Step 4: Click the Apply button and click Continue to restart the access point.

Tags: , ,

Apr 27

You can change the user name and password within the web-based configuration utility that is built-in to the access point.

Step 1: Open your web browser such as Internet Explorer. Enter the IP address of the D-Link access point (default is 192.168.0.50) and press Enter.

Step 2: Enter your username (admin) and your password (leave blank by default). Click OK.

Step 3: Click on the Tools tab at the top and then click Admin.

Step 4: Enter your new user name and then enter the old password (if any). Enter your new password and click Apply. After the access point restarts, you will be required to enter your new user name and password.

Tags: , , ,

Apr 25

The firewall security features built into the D-Link DI-624 router prevent users from accessing the video from the D-Link DCS-2120 over the Internet. The router connects to the Internet over a series of numbered ports. The ports normally used by the D-Link DCS-2120 are blocked from access over the Internet. Therefore, these ports need to be made accessible over the Internet. This is accomplished using the Virtual Server function on the DI-624 router. The Virtual Server ports used by the camera must be opened through the router for remote access to your camera. Virtual Server is accessed by clicking on the Advanced tab of the router screen.

Follow these steps to configure your router’s Virtual Server settings:

**In this example, we are using the DI-624. The Virtual Server interface may differ depending on your router*.

Follow these steps to configure the Virtual Server settings of the D-Link DI-624:

Step 1: Open a web browser such as Internet Explorer and enter the IP address of your router (192.168.0.1). Enter username (admin) and your password (leave blank).

Step 2: Click on the Advanced tab and then the Virtual Server button on the left.

Step 3: Click Enabled.

Step 4: Enter a different name for each entry.

Step 5: Enter your camera’s local IP Address Private IP field.

Step 6: Select TCP for HTTP port and both (TCP and UDP) for RTSP port.

Step 7: If you are using the default camera port settings, enter 80 into the Public and Private Port section, click Apply.

Step 8: Scheduling should be set to Always so that the camera images can be accessed at any time.

Repeat the above steps adding the port 554 to both the Public and Private Port sections. A check mark appearing before the entry name will indicate that the ports are enabled.

Important: Some ISPs block access to port 80 and other commonly used Internet ports to conserve bandwidth. Check with your ISP so that you can open the appropriate ports accordingly. If your ISP does not pass traffic on port 80, you will need to change the port the camera uses from 80 to something else, such as 800. Not all routers are the same, so refer to your user manual for specific instructions on how to open ports.

Enter valid ports in the Virtual Server section of your router. Please make sure to check the box next to the D-Link camera name on the Virtual Server List to enable your settings.

Tags: , , ,

Apr 25

Note: The following FAQ demonstrates the usage of the Command Prompt in Windows XP.

Step 1: Click Start and select Run.

Step 2: In the Run command box, type cmd and click OK.

Step 3: In the command prompt, type ipconfig/release.

Step 4: After the IP addresses are released, type ipconfig/renew.

Step 5: Your adapter will send a request for a DHCP (automatically) obtained IP address, netmask, gateway, and DNS if auto-DNS is enabled.

If you are having problems obtaining an IP address using DHCP, you may want to try to static (manual) the IP address. Click here for assistance.

Note: Verify that you have a DHCP server on your D-Link network, such as a router. Most routers have a setting to disable or enable DHCP.

Tags: , , ,



 
1 2 3 Next
css.php