Mar 25

D-Link DNS-320L Quick Install Guide Manual Installation

Step 1:

Remove the top cover of your device by pressing the push button in and then lift the cover up.

Step 2:

Attach the strap to your hard drive(s) with the supplied screws.

Step 3:

Insert one or two 3.5” SATA hard drive(s) into the drive bay until they are firmly seated. Then, re-attach the top cover.

Step 4:

Plug an Ethernet cable to the Ethernet port on the back of the device and plug the other end to your network via a router or switch, or directly to a computer for configuration.

Step 5:

Connect the power adapter to the device and then connect the other end into a power outlet or surge protector. Press the power button on the front of the device to turn the device on.

Step 6:

Open a web browser and enter the IP address of the D-Link DNS-320L to access the Web UI. If you have a DHCP-enabled router on your network, you may need to check the DHCP table to see what IP address the DNS-320L was assigned.

Note: The computer used to access the ShareCenter® web-based configuration manager must be on the same subnet as the ShareCenter®.

If your network is using a DHCP server and the computer receives IP settings from the DHCP server, the ShareCenter® will automatically be in the same subnet.

Step 7:

Select System Administrator and click the Login button (leave the password blank by default). Once you are logged in, click Management and then click Setup Wizard. Follow the on-screen instructions to configure your D-Link DNS-320L.

Note: Please refer to the manual for more information.

Tags: , ,

Mar 25

Minimum System Requirements

• One or two 3.5” SATA Hard Drive(s)
• Computer with: 1GHz processor/512MB RAM/200MB available disk space/CD ROM drive
• Internet Explorer version 7.0 or Mozilla Firefox 3.0 or above
• Windows® 7, Vista®, or XP (with Service Pack 2); Mac OS® X (10.5 or above)

Installation – Windows® Only

The Setup Wizard on the CD-ROM will give you step-by-step instructions how to connect, install, and configure your D-Link DNS-320L.

Step 1:

Insert the supplied CD-ROM into your computer. When the autorun screen appears, click Install.

Step 2:

Follow the on-screen instructions. Once completed you can log into the DNS-320L for advanced configuration.

Installation – Mac OS® X Only

The Setup Wizard on the CD-ROM will give you step-by-step instructions how to connect, install, and configure your DNS-320L.

Step 1:

Insert the supplied CD-ROM into your computer and navigate to the Setup Wizard > Mac folder. Launch the setup wizard file.

Step 2:

Follow the on-screen instructions. Once completed you can log into the DNS-320L for advanced configuration.

Tags: ,

Mar 20

The easiest and most secure way to connect your wireless devices to the router is WPS (Wi-Fi Protected Setup). Most wireless devices such as wireless adapters, media players, Blu-ray DVD players, wireless printers and cameras will have a WPS button (or a software utility with WPS) that you can press to connect to the DIR-845L router. Please refer to your user manual for the wireless device you want to connect to make sure you understand how to enable WPS. Once you know, follow the steps below:

Step 1 – Press the WPS button on the DIR-845L for about 1 second. The Internet LED on the front will start to blink.

Step 2 – Within 2 minutes, press the WPS button on your wireless client (or launch the software utility and start the WPS process).

Step 3 – Allow up to 1 minute to configure. Once the Internet light stops blinking, you will be connected and your wireless connection will be secure with WPA2.

Tags: ,

Mar 18

Enable Wireless:

Check the box to enable the wireless function. If you do not want to use wireless, uncheck the box to disable all the wireless functions.


Select the time frame that you would like your wireless network enabled.The schedule may be set to Always. Any schedule you create will be available in the drop-down menu. Click New Schedule to create a schedule.

Wireless Network Name:

Service Set Identifier (SSID) is the name of your wireless network. Create a name for your wireless network using up to 32 characters. The SSID is case-sensitive.

802.11 Mode:

Select one of the following:
802.11b Only – Select only if all of your wireless clients are 802.11b.
802.11g Only – Select only if all of your wireless clients are 802.11g.
802.11n Only – Select only if all of your wireless clients are 802.11n.
Mixed 802.11g and 802.11b – Select if you are using both 802.11g and 802.11b wireless clients.
Mixed 802.11n and 802.11g – Select if you are using both 802.11n and 802.11g wireless clients.
Mixed 802.11n, 11g, and 11b – Select if you are using a mix of 802.11n, 802.11g, and 802.11b wireless clients.

Enable Auto Channel Scan:

The Auto Channel Scan setting can be selected to allow the DIR-865L to choose the channel with the least amount of interference.

Wireless Channel:

Indicates the channel setting for the DIR-865L. By default the channel is set to 6. The Channel can be changed to fit the channel setting for an existing wireless network or to customize the wireless network. If you enable Auto Channel Scan, this option will be greyed out.

Channel Width:

Select the Channel Width:
Auto 20/40 – This is the default setting. Select if you are using both 802.11n and non-802.11n wireless devices.
20MHz – Select if you are not using any 802.11n wireless clients.

Visibility Status:

Select Invisible if you do not want the SSID of your wireless network to be broadcasted by the DIR-865L. If Invisible is selected, the SSID of the DIR-865L will not be seen by Site Survey utilities so your wireless clients will have to know the SSID of your DIR-865L in order to connect to it.

Wireless Security:

Refer to page 46 for more information regarding wireless security.

Wireless Bridge Mode

If you want to wirelessly connect multiple Ethernet-enabled devices such as game consoles, media players, or network attached storage (NAS) devices you can set the DIR-865L to Bridge mode. You must have a wireless router for this feature.

Note: For 802.11ac performance, you must connect to another 802.11ac wireless router. The DIR-865L will automatically adjust to the connection type of your router.

To configure your DIR-865L router to bridge mode, follow the steps below:

Step 1 – From the Setup > Internet page, click Manual Internet Connection Setup and then check the Enable Wireless Bridge box.

Click Save Settings and then click OK to the pop-up message.

Note: When you enable Bridge mode, the DIR-865L’s default IP address will change to

Step 2 – The following message will appear. The router will automatically reboot.

Step 3 – Once the router reboots, you may get a “connect display page” error on your web browser. This is because the IP address of the router changed. In your web browser, enter to access the web interface.

Step 4 – At the login screen, enter admin for the User Name and enter your password (leave blank by default).

Step 5 – From the Setup > Wireless Settings page, click the Site Survey button. This will display a list of wireless networks in your area.You may also manually enter the wireless network name you want to connect to (SSID) and any security/encryption settings (from the Security Mode drop-down menu). Enter your wireless network information, click Save Settings, and then skip to step 7.

Step 6 – When the site survey screen appears, select the network you want to connect to (click the radio button under Select) and then click Connect.

If the network is secure/encrypted, you will need to enter the passphrase/encryption key.Please allow a minute to connect.

Step 7 – Once connected, any Ethernet device connected to the DIR-865L will connect to the wireless network.

Note: Wireless clients cannot connect to the DIR-865L while in bridge mode.Also, the Internet port on the D-Link DIR-865L in Bridge mode will not function.

Tags: , ,

Mar 18

D-Link offers an app for your iPad, iPod Touch, or iPhone (iOS 4.3 or higher) to install and configure your D-Link DIR-845L router.

Step 1:

From your iPad, Touch, or iPhone, go to the iTunes Store and search for ‘D-Link’. Select QRS Mobile and then download it.You may also scan this code to download.

Step 2:

Once your app is installed, you may now configure your router.Connect to the router wirelessly by going to your wireless utility on your device. Scan for the wireless network name (SSID) as listed on the supplied info card. Select and then enter your security password (Wi-Fi Password).

Step 3:

Once you connect to the router, launch the QRS mobile app and it will guide you through the installation of your D-Link DIR-845L router.

Tags: , , ,

1 2 3 Next