Sep 19

First, check that your smartphone or tablet is wirelessly connected to the DIR-505. Sometimes these devices switch wireless networks without notifying the user.

Next, in the SharePort Mobile app, tap on the Gear icon in the top-right corner to access the SharePort Settings.

Ensure the User Name and Password for your DIR-505 is entered correctly (NOTE: This will be the user name and password used to log into the DIR-505 web interface, and not the wireless name and passphrase.)

If you are still unable to view the contents, reboot your device and open the SharePort Mobile app again.

Tags: , ,

Sep 19

How to configure the WAN settings on D-Link DI‑634M Super G with MIMO Wireless Router

Select your WAN connection:

·  Dynamic IPAddress

·  Static IPAddress

·  PPPoE

·  PPTP

·  L2TP

·  BigPondCable


 

Dynamic IPAddress

Step 1 Open a web browser and type the IP addressof the DI-634M in the address bar (default is192.168.0.1).

Step 2 The default username isadmin (all lower case) and the default password isblank (nothing). Click on OK.

Step 3 Click on the Home tab atthe top and then click on WAN on the leftside.

Step 4 Select Dynamic IPAddress.

Step 5 If your ISP requires a host name enter itnext to Host Name. If you want to use another MAC addressother than the MAC address of the WAN port enter it next to MACAddress and select Use MAC.

Step 6 Click on Apply to saveyour settings.


 

Static IPAddress

Step 1 Open a web browser and type the IP addressof the DI-634M in the address bar (default is192.168.0.1).

Step 2 The default username isadmin (all lower case) and the default password isblank (nothing). Click on OK.

Step 3 Click on the Home tab atthe top and then click on WAN on the leftside.

Step 4 Select Static IPAddress.

Step 5 Enter the IP address, subnet mask, ISPgateway address, and primary DNS and secondary (optional) DNSserver addresses.

Step 6 Click on Apply to saveyour settings.


 

PPPoE

Step 1 Open a web browser and type the IP addressof the DI-634M in the address bar (default is192.168.0.1).

Step 2 The default username isadmin (all lower case) and the default password isblank (nothing). Click on OK.

Step 3 Click on the Home tab atthe top and then click on WAN on the leftside.

Step 4 Select PPPoE.

Step 5 Select PPPoE andconfigure the following:

  • User Name – Enter your username
  • Password – Enter your password
  • Verfify Password – Confirm your password
  • Service Name – Enter a service name ifrequired by your ISP (optional)
  • MAC Address Enter a MAC address if required byyour ISP (optional)
  • Primary DNS Server – The IP address of theDomain Name Server. Your ISP will provide this information if it isrequired; otherwise, leave this box set to 0.0.0.0.(optional)
  • Secondary DNS Server – The IP address of theDomain Name Server. Your ISP will provide this information if it isrequired; otherwise, leave this box set to 0.0.0.0.(optional)
  • Maximum Idle Time – Enter the amount of time(in minutes) in which the DI-634M will disconnect your Internetconnection after inactivity
  • MTU – Enter the MTU. This is usually1492.

Connection Mode Select

  • Always on – A connection to the Internet isalways maintained.
  • Manual – You have to open up the Web-basedmanagement interface and click the Connect button manually any timethat you wish to connect to the Internet.
  • Connect on demand – A connection to theInternet is made as needed; and the connection is dropped after”Maximum Idle Time” minutes of no activity.

Step 6 Click on Apply to saveyour settings.


 

PPTP

Step 1 Open a web browser and type the IP addressof the DI-634M in the address bar (default is192.168.0.1).

Step 2 The default username isadmin (all lower case) and the default password isblank (nothing). Click on OK.

Step 3 Click on the Home tab atthe top and then click on WAN on the leftside.

Step 4 Select PPTP and configurethe following:

  • IP Address – Enter the IP address
  • Subnet Mask – Enter the subnet mask
  • Default Gateway – Enter the Default Gateway IPaddress
  • Server IP address – Enter the Server IPaddress
  • Username – Enter your Username
  • Password – Enter your password
  • Verify Password – Confirm your password
  • Maximum Idle Time – Enter the amount of time(in minutes) in which the DI-634M will disconnect your Internetconnection after inactivity
  • MTU – Enter the MTU. This is usually1452.

Connection Mode Select

  • Always on – A connection to the Internet isalways maintained.
  • Manual – You have to open up the Web-basedmanagement interface and click the Connect button manually any timethat you wish to connect to the Internet.
  • Connect on demand – A connection to theInternet is made as needed; and the connection is dropped after”Maximum Idle Time” minutes of no activity.

Step 5 Click on Apply to saveyour settings.


 

L2TP

Step 1 Open a web browser and type the IP addressof the DI-634M in the address bar (default is192.168.0.1).

Step 2 The default username isadmin (all lower case) and the default password isblank (nothing). Click on OK.

Step 3 Click on the Home tab atthe top and then click on WAN on the leftside.

Step 4 Select PPTP and configurethe following:

  • IP Address – Enter the IP address
  • Subnet Mask – Enter the subnet mask
  • Default Gateway – Enter the Default Gateway IPaddress
  • Server IP address – Enter the Server IPaddress
  • Username – Enter your Username
  • Password – Enter your password
  • Verify Password – Confirm your password
  • Maximum Idle Time – Enter the amount of time(in minutes) in which the DI-634M will disconnect your Internetconnection after inactivity
  • MTU – Enter the MTU. This is usually1452.

Connection Mode Select

  • Always on – A connection to the Internet isalways maintained.
  • Manual – You have to open up the Web-basedmanagement interface and click the Connect button manually any timethat you wish to connect to the Internet.
  • Connect on demand – A connection to theInternet is made as needed; and the connection is dropped after”Maximum Idle Time” minutes of no activity.

Step 5 Click on Apply to saveyour settings.


 

BigPondCable

Step 1 Open a web browser and type the IPaddress of the DI-634M in the address bar (default is192.168.0.1).

Step 2 The default username isadmin (all lower case) and the default password isblank (nothing). Click on OK.

Step 3 Click on the Home tab atthe top and then click on WAN on the leftside.

Step 4 Select BigPond Cable andconfigure the following:

  • Username – Enter the Username
  • Password – Enter the Password
  • Verify Password – Re-enter password
  • Auth Server – Enter the Authentication Serveraddress
  • MAC Address – Enter your MAC address

Step 5 Click on Apply to saveyour settings.

Tags: , ,

Sep 16

The flashing Status light on the front of your D-Link router indicates that it is operational.  Itdoes not show whether the router has been configured or not, so itmay still be necessary to set up Internet or wirelessconnectivity.

If the Status light is on permanently, or staysoff, please try the following suggestions:

1) Power off the device and leave it off forabout 20 seconds.  Power it on again and check the Status light.
2) Run through the factory reset procedure for your router.

If the above steps still result with the Status light on permanently or stays off, please contact our support team.

Tags: , ,

Sep 16

Step 1: Open a web browser and type the IP address of the D-Link DIR series router into the address bar (default is http://192.168.0.1). Press Enter

Step 2: The default username is admin (all lower case) and the default password is blank (nothing). Click on OK.

Step 3: Click on the Setup tab at the top and then click on Wireless Settings on the lefthand side.

Step 4: From the Wireless Security Mode dropdown menu, select WPA-Personal encryption.

Step 5: From the WPA Mode dropdown, Under WPA, select the form of WPA you would like to use.

Use WPA or WPA2 mode to achieve a balance of strong security and best compatibility. This mode uses WPA for legacy clients while maintaining higher security with stations that are WPA2 capable. Also the strongest cipher that the client supports will be used.

How to secure the wireless signal of D-Link DIR Series Router

For best security, use WPA2 Only mode. This mode uses AES(CCMP) cipher and legacy stations are not allowed access with WPA security.

For maximum compatibility, use WPA Only. This mode uses TKIP cipher. Some gaming and legacy devices work only in this mode. To achieve better wireless performance use WPA2 Only security mode (or in other words AES cipher).

Step 6: In the Pre-Shared Key box, enter the desired Pre-shared key.

This is the “password that allows communication between you’re encrypted client (e.g. the PSP or your wireless computer) and the encrypted wireless signal coming from the D-Link router. This password must contain at least 8 characters, the characters can be anything you can create from your keyboard.

Step 7: Click on Save Settings to save your settings.

Tags: , ,

Sep 10

To perform a factory reset on D-LINK router, please follow the steps below.

Step 1: With the unit on, place a paper clip into the hole on the back of the unit labeled Reset.

Step 2: Hold paper clip down for 10 seconds and release.

Step 3: The unit will reboot on its own. Once the WLAN light stops blinking, the unit is reset.

Resetting the router does not reset the firmware to an earlier version. It will change all settings back to factory defaults.

Note: The factory defaults username is admin, and there is no password.

Tags: , ,



 
1 2 3 Next
css.php