May 15

Your AP may be showing offline because the Nuclias Connect server IP address does not match the server IP settings in the access point. Check to make sure the access point is powered on. It is recommended that your Nuclias Connect Server has a statically assigned IP Address.

Step 1: Log into your access point and confirm the Nuclias Connection status

NOTE: This example shows the Connection status as Disconnected and the server IP address is

Step 2: Check the IP address on the computer that is running the Nuclias connect software

NOTE: This computer IP address is Which is different then the server IP address on the access point. This is why the Nuclias connect software is showing the AP offline

Step 3: Launch the Nuclias Connect Software

Step 4: Click on System > Settings

Step 5: Click on the Connection tab and change the Device access address to the IP address of the computer.

NOTE: In this example the IP address is

– Click Save

Step 6: Click on Configuration > Create Profile

Step 7: Click on Discovery icon for your profile

NOTE: You should see your profile listed. In this example my profile is called PS-HOME

Step 8: Select your discover settings, then tap NEXT

Step 9: Click on Start Discovery

Step 10: Select your AP and click Apply, then Exit

Step 11: Click on Monitor and your AP should show online

Tags: ,

May 15

Push notifications are enabled on the D-Link DCH-S161 by default.

To test your water sensor for push notifications, dip the probe into water for 15 to 20 seconds. The sensor will power on, connect to your Wi-Fi and then send push notifications to your device. This may take approximately 15 to 20 seconds.

NOTE: When in power saving mode, the device is still functional. The device will automatically wake-up as soon as water is detected.

Power Saving Mode                                                        Online

Tags: ,

May 15

NOTE: Bridge Mode allows you to connect the COVR system to your existing router. In Bridge Mode the routing functionality will be disabled, and your COVR system will work as an access point.

NOTE: In Bridge mode, Point A needs to be connected via Ethernet cable to your existing router

NOTE: The COVR router needs to be setup as a router first. Then you can configure your COVR router in Bridge Mode.

Step 1: Open your Internet browser (Internet Explorer/Firefox) and enter http://covr.local./ 

Step 2: Enter your admin password and tap, Log In

Step 3: Tap on Settings, and then Operation

Step 4: Select Bridge Mode, then tap Save


Step 5:  Tap OK

NOTE: Once the COVR system has been set to bridge mode it gets an IP Address from your existing router. If needed you can log into the COVR system with http://dlinkap.local

Tags: ,

May 12

To set your computer to obtain IP address automatically (DHCP):

Step 1. Choose Apple menu > System Preferences, then click Network.

Step 2. Select the network connection you want to use (such as Ethernet) in the list.

Step 3. Click the ‘Configure IPv4’ pop-up menu, then choose this option: Using DHCP.

To set your computer with a static IP address:

Step 1. Choose Apple menu > System Preferences, then click Network.

Step 2. Select the network connection you want to use (such as Ethernet) in the list.

Step 3. Click the ‘Configure IPv4’ pop-up menu, then choose this option: Manually.

Step 4. Enter the address in the IP Address field. Specify other information such as the subnet mask, router address, and Domain Name System (DNS) server address. To enter the DNS server address, click Advanced, click DNS, then click the Add button + and enter the address.

Tags: ,

May 12

Find a network connection icon in the bottom right corner of your screen. Right-click on it and select ‘Open Network and Sharing Center’. Then click on ‘Change Adapter Settings’ on the menu on the left.

Double-click on the ‘Local Area Connection’ (or ‘Wireless Network Connection’, whichever you are using) icon.

To check your network adapter’s current IP address click on ‘Details…’

To change your network adapter IP settings:
Step 1. Double-click on the ‘Local Area Connection’ (or ‘Wireless Network Connection’) and click on ‘Properties’.

Step 2. Highlight the Internet Protocol v4 and click Properties.

Step 3. Select the ‘Use the following IP Address’ option and enter your IP settings for your network.

If connecting to a router, make sure the Default Gateway and a DNS server is the IP address of the router (e.g. or You can also specify your provider’s DNS servers’ addresses.

Tags: , ,