Nov 11

The firewall security features built into the router prevent users from accessing the video from the D-Link DCS-5220 over the Internet. The router connects to the Internet over a series of numbered ports. The ports normally used by the DCS-5220 are blocked from access over the Internet. Therefore, these ports need to be made accessible over the Internet. This is accomplished using the Virtual Server function on the router. The Virtual Server ports used by the camera must be opened through the router for remote access to your camera.

**In this example, we are using the D-Link DI-624. The Virtual Server interface may differ depending on your router**.

Follow these steps to configure the Virtual Server settings of the DI-624:

Step 1: Open a web browser such as Internet Explorer and enter the IP address of your router (192.168.0.1). Enter username (admin) and your password (leave blank).

Step 2: Click on the Advanced tab and then the Virtual Server button on the left.

Step 3: Click Enabled.

Step 4: Enter a different name for each entry.

Step 5: Enter your camera’s local IP Address in the Private IP field.

Step 6: Select TCP for HTTP port, both (TCP and UDP) for RTSP and both (TCP and UDP) for 5556 – 5559 ports.

Step 7: If you are using the default camera port settings, enter 80 into the Public and Private Port section, click Apply.

Step 8: Scheduling should be set to Always so that the camera images can be accessed at any time.

Repeat the above steps adding the port 554 to both the Public and Private Port sections. A check mark appearing before the entry name will indicate that the ports are enabled.

Important: Some ISPs block access to port 80 and other commonly used Internet ports to conserve bandwidth. Check with your ISP so that you can open the appropriate ports accordingly. If your ISP does not pass traffic on port 80, you will need to change the port the camera uses from 80 to something else, such as 800. Not all routers are the same, so refer to your user manual for specific instructions on how to open ports.

Enter valid ports in the Virtual Server section of your router. Please make sure to check the box next to the camera name on the Virtual Server List to enable your settings.

Tags: ,

Nov 10

Step 1: Launch D-ViewCam and click Schedule Configuration

A10562_image1

Step 2: Select the camera(s) you want to apply the recording schedule to, select or create a schedule (by default it is 24 Hours) and click Configure

A10562_image2

Step 3: Under Mode, ensure Always Record is selected

Step 4: Under the Time Section, specify the time when you want the recording to occur and click OK.

Note: If you want to record Audio, ensure to select “Record Audio” from the audio section

A10562_image3

Click OK to close the Encoding Options and Click OK again to Close the Schedule Configuration.

Step 5: Click the Start Menu and click Start Recording Schedule

A10562_image4

Note: A Red circle will appear in the top right corner of each camera with Recording Configured. This indicates that it is recording.

A10562_image5

Tags: ,

Nov 09

Step 1 Log into your camera through the web interface.

Step 2 Select Configuration on the left.

Step 3 Click Motion Detection on the left.

Step 4 Click Enable Motion Detection.

Step 5 Click New and resize the motion detection window. Click the Window Name box and enter a name. Next, set sensitivity and percentage.

A10420_image1

Step 6 Click Apply.

Step 7 Go to Tools and then select Applications on the left.

Step 8 Select your desired schedule.

Note: If you wish to set the schedule of motion detection for every day, select All the time except for the above schedule.

Step 9 Click Event Operation.

Step 10 Select the motion window(s) you would like the event to watch.

Step 11 Select the trigger action.

Step 12 Once you have selected the proper trigger action, choose where snapshots will be sent to, Email or FTP.

A10420_image2

Step 13 Click Apply.

Tags: ,

Nov 08

Note: mydlink Cloud Service registration requires the camera’s admin password.

Step 1: Launch the D-Link mydlink Baby app.

A10859_image1

Step 2: Tap the camera which you want to change the password for.

A10859_image2

Step 3: Tap the settings icon in the top right-hand corner of the screen.

A10859_image3

Step 4: Tap the arrow to expand the Camera info section

A10859_image4

Step 5: To change the administrator password, enter the existing administrator password in the Current Password field (leave blank if you have not changed it from the default), and enter a new password in the New Password field and again in the Confirm Password field.

A10859_image5

Step 6: Tap Apply to save the configuration.

A10859_image6

Tags: ,

Nov 08

Step 1: Launch the mydlink Baby app.

 

A10858_image1

 

Step 2: Tap the camera which you want to use to play the lullaby.

A10858_image2

Step 3: Tap the lullaby button (found on the bottom of the Live View screen, fourth from the left). Tap buttons 1-5 to choose a specific lullaby, “ALL” to play them all in sequence, or “OFF” to stop playing a lullaby. Alternatively, press the lullaby button on top of the camera unit to toggle playing a lullaby on or off.

A10858_image3

Tags: , ,



 
Prev 1 2 3 ... 12 13 14 15 16 17 18 19 20 21 22 Next
css.php