Jan 28

To allow traffic from the internet to enter your local network, you will need to open up ports or the router will block the request.

Because our routers use NAT (Network Address Translation), you can only open a specific port or ports to one computer at a time. For example: If you have 2 web servers on your network, you cannot open port 80 to both computers. You will need to configure 1 of the web servers to use port 81. Now you can open port 80 to the first computer and then open port 81 to the other computer.

For the DI-514, DI-524, DI-604, DI-614+, DI-624, DI-704P (revC), DI-704UP, DI-754, DI-764, DI-774, and DI-784:

Step 1: Open your web browser and enter the IP address of your D-Link router (192.168.0.1). Enter username (admin) and your password (blank by default).

Step 2: Click on the Advanced tab at the top and then click Virtual Server on the left side.

Step 3: Check Enabled to activate entry.

Step 4: Enter a name for your virtual server entry.

Step 5: Next to Private IP, enter the IP address of the computer on your local network that you want to allow the incoming service to.

Step 7: Enter the port information next to Private Port and Public Port. The private and public ports are usually the same. The public port is the port seen from the WAN side, and the private port is the port being used by the application on the computer within your local network.

Step 8: Enter the Schedule information.

Step 9: Click Apply and then click Continue.

For DI-704P (rev.B), DI-707P, DI-714P+, DI-804HV, DI-808HV, and DI-824VUP users:

Step 1: Open a web browser and enter the IP address of your router (192.168.0.1). Enter admin for your username and then your password (blank by default).

Step 2: Click on the Advanced tab and then Virtual Server on the left side.

Step 3: Enter the following information:

Check the box next to Enable.
Next to Service Ports, enter the port or range of ports you want to open.
Next to Service IP, enter the IP address of the computer you want to open the port to.
Click Always next to Schedule or enter the time frame that you want.

Step 4: Click Apply and then click Restart to save your changes.

How to open the ports on D-Link DIseries router

Tags: ,

Jan 27

The following article is for for most Cable connections such as Adelphia, AOL (Earthlink), ATnT, Cox, Comcast, Charter, Knology, Optimum Online (Cablevision), RCN, RoadRunner (Time Warner), and Rogers.

If you have trouble connecting to your modem, you may need to lock the speed down on the WAN port of your router to 10Mbps.

In the web-based configuration utility for the D-Link DIR-655, go to Tools > Misc and the option to select the WAN speed will be towards the bottom.

Step 1: Login the web-based configuration by typing in the IP address of the router (default:192.168.0.1) in your web browser. The username is admin  and the password is blank (nothing).

If the router is already online, you will be taken to the STATUS page after logging in. If this is the case, the router is connected and you do not need to continue with this FAQ.

Step 2: Click the Setup tab and then click the Internet button.

DIR-655-a

Step 3: Click Manual Configure.

DIR-655-b

Step 4: Dynamic IP Address is the default value, however, if Dynamic IP Address is not selected as the WAN type, select Dynamic IP Address from the drop down menu. Click Clone Mac Address. Click on Save Settings to save the changes.

DIR-655-c

Step 5: Click on Status. Under WAN, Click DHCP Renew. If it does not get an IP address or times out, then continue with Step 6.

Step 6: Power cycle the cable modem and router using the following steps:

  • Turn the cable modem off (first)
  • Turn the router off
  • Leave them off for 2 minutes**
  • Turn the cable modem on (first)
  • Wait until you get a solid cable light on the cable modem
  • Turn the router on
  • Wait 30 seconds
  • Step 7: Follow Step 1 again to log back into the web configuration. Click the Status tab and click the Device Info button. If you do not already have a public IP address under the WAN heading, click on the DHCP Renew button.

    Tags: ,

    Jan 25

    The most important step is creation of a reasonable networking scheme, our FAQs will use the below scheme.

    Step 1: Choose Setup->VPN and then Add->IPsec VPN. Fill in the following values.

    DIR-330VPN

    Name: Whatever you like.
    Local Net/Mask: Enter the LAN Net of the DIR.
    Remote IP: Enter the WAN_IP of the Hub
    Remote Local LAN Newt /Mask: Enter the Concentrated Network from the Hub.
    Authentication->Pre-shared Key: Whatever you like
    NAT-T Enable: Checked
    Keep Alive: Keep Alive
    PSF: Perfect Forward Security is on.

    Step 2: Choose Save Settings.

    Tags: ,

    Jan 24

    This article teach you how to D-Link router to restore factory settings,di-524 as an example.

    How to reset router back to the factory default settings?

    Step 1 With the unit on, place a paper clip into the hole on the back on the unit labeled Reset.

    Step 2 Hold paper clip down for 10 seconds and release. (Note: Do not repower unit during this procedure.)

    Step 3 The unit will reboot on its own. Once the WLAN light stops blinking, the unit is reset.

    Resetting the router does not reset the firmware to an earlier version. It will change all settings back to factory defaults.

    Tags: , ,

    Jan 16

    This article teaches you VPN config about D-Link Firewall and DI-804HV,With the DFL-800 as an example.

    1. Go to “System” → “DNS” and enter a working DNS server IP, here we use our ISP’s DNS server.

    DFL-800a

    2. Go to “System” → “Misc. Clients” → “Add” to add a DDNS client, here we choose dyndns.org DDNS client.

    DFL-800b

    3. Then enter the full domain name and your account info.

    DFL-800c

    4. Go to “Objects” → “Address book”, previously, we use an IP on the remote gateway, here, just change the IP to the domain name, here we assume the other side (DI-804HV also uses DDNS and has the domain test1.dyndns.org setup). Click on the “remote-gw” object, and modify the IP to “dns:test1.dyndns.org”. Make sure “dns:” is entered before the domain name.

    DFL-800d

    5. In DI-804HV, just replace the remote gateway IP to the DDNS domain name we set up in D-Link DFL-800 (test.dyndns.org)

    DI-804HV

    Tags: , ,



     
    Prev 1 2 3 ... 41 42 43 44 45 46 47 48 49 50 51
    css.php