Jul 21

View D-Link DWL-G730AP log is very simple. As long as the following sub-steps on it:

Step 1: Open a web browser and type the IP address of the D-Link DWL-G730AP in the address bar (default is 192.168.0.30). Press Enter.

Step 2: The default username is admin and the default password is blank (nothing). Click OK.

Step 3: Click the Status tab and then click Log to the left.

dlink-log

Step 4: This displays the activity log for your access point. The buttons located above the log can be used to perform certain actions.

First Page: View the first page of the log.

Last Page: View the last page of the log.

Previous: View the previous page of the log.

Next: View the next page of the log.

Clear: Clear (delete) the entire log.

Log Settings: Configure advanced settings for the log such as email notifications.

Tags: , ,

Jul 21

D-Link DWL-G730AP has 4 Filters can be configured:

•IP Filters
URL Blocking
MAC Filters
Domain Blocking

Today I will teach you how to set up D-Link filters.

1.IP Filters

IP filters block access to ports or a series of ports from an IP address on the local network (LAN). For example, if you did not want the computer with IP address 192.168.0.100 to access the Internet, then you would block that IP address from accessing port 80.

Step 1: Open a web browser and type the IP address of the DWL-G730AP in the address bar (default is 192.168.0.30). Press Enter.

Step 2: The default username is admin (all lower case) and the default password is blank (nothing). Click OK.

Step 3: Click the Advanced tab then click Filters on the left.

Step 4: Select the IP Filters radio button.

dlink-filter1

Step 5: Select the Enabled radio button.

Step 6: In the first field next to IP enter the IP address you want to filter access from. If you want this to apply to a range of IP addresses, then enter the ending IP address in the second field.

Step 7: In the first field next to Port enter the port you want to block. To block a range of ports, enter the ending port number in the second field, then select the protocol type (TCP, UDP, or Both) from the drop-down list next to Protocol Type.

Step 8: Next to schedule select the Always radio button to always deploy this filter, or select the From radio button to set a schedule using the time and day drop-down boxes below.

Step 9: Click Apply and then click Continue to save the settings.

2.URL Blocking

URL Blocking is used to block web sites that contain certain keywords.

Step 1: Open a web browser and type the IP address of the DWL-G730AP in the address bar (default is 192.168.0.30). Press Enter.

Step 2: The default username is admin (all lower case) and the default password is blank (nothing). Click OK.

Step 3: Click the Advanced tab then click Filters on the left.

Step 4: Select the URL Blocking radio button.

dlink-filter2

Step 5: Select the Enabled radio button.

Step 6: In the text box below enter a keyword to block. To delete a keyword, select it from the box below the text box, and click the Delete button.

Step 7: Click Apply to add the keyword to the list.

3.MAC Filters

MAC Filters allow you to allow or deny access to the LAN by specifying MAC addresses.

Step 1: Open a web browser and type the IP address of the DWL-G730AP in the address bar (default is 192.168.0.30). Press Enter.

Step 2: The default username is admin (all lower case) and the default password is blank (nothing). Click OK.

Step 3: Click the Advanced tab then click Filters on the left.

Step 4: Select MAC Filters using the radio buttons.

dlink-filter3

Step 5: In the section MAC Filters, select the radio button for the mode you would like to use.

Disabled – Disables this feature and will allow all wireless clients to connect.
Allow – Blocks all clients except for what you enter in the list.
Deny – Allows all clients except for what you enter in the list.

Step 6: Enter the name used to identify the entry next to Name.

Step 7: Enter the Ethernet MAC address that you wish to Allow or Deny next to MAC Address.

Step 8: Click Apply and then click Continue to save the settings.

4.Domain Blocking

Domain blocking lets you allow or deny access to certain websites.

Step 1: Open a web browser and type the IP address of the DWL-G730AP in the address bar (default is 192.168.0.30). Press Enter.

Step 2: The default username is admin (all lower case) and the default password is blank (nothing). Click OK.

Step 3: Click the Advanced tab then click Filters on the left.

Step 4: Select Domain Blocking using the radio buttons.

dlink-filter4

Step 5: In the section Domain Blocking, select the radio button for the mode that you would like to use.

Disabled – Disable this feature and will allow all clients on the LAN to access any website.
Allow – Permits access to all websites except domains specified in the Blocked Domains section.
Deny – Allows access only to domain specified in the Permitted Domains section.

Step 6: In the Permitted Domains section, enter a domain to permit.
In the Blocked Domains section, enter a domain to block.

– or

To delete a keyword, select it and click the Delete button.

Step 7: Click Apply to add the domain the list.

Tags: , , , ,

Mar 10

DWA-130_rev A1: Hardware revision A1 was the original DWA-130. This revision was not implement with WPS functionality until driver version 1.30 in Windows systems. You may check for the latest here. There is no physical button to engage the WPS connectivity but rather it´s performed through the Utility software.

DWA-130_rev B1: Hardware revision B1 has supported WPS functionality through software just as rev A1. Please check for the latest driver here for Windows and Mac systems.

DWA-130_rev C1: Hardware revision C1 supports WPS functionality same as A1 and B1. Find the latest driver here for Windows, Mac and Linux systems.

DWA-130_rev D1: Hardware revision D1 is the last WPS functionality through software only, same as A1, B1, and C1. Find the latest driver here for Windows systems.

DWA-130_rev C2: Hardware revision C2 is the first DWA-130 with hardware change, by implementation of a WPS push button. The Utility application can still perform the WPS connection. Use of the physical button may be simpler to perform. First press the WPS button on the adapter, then press the WPS button on your access point or wireless router within 2 minutes to establish connectivity.

DWA-130_rev E1: Hardware revision E1 has WPS push button functionality same as C2. Find the latest drivers here for Windows systems.

Tags:

Mar 10

Step 1: Right click the Wireless status icon in the task bar, to open the Wireless Manager.

Step 2: On the Wireless Manager click on WPS

Step 3: On the Wi-Fi Protected Setup select the PIN option

Step 4: Enter the PIN number on the Router or Access Point.

Step 5: The wireless card will establish the connection with the Router or Access Point.

Step 6: At this point the wireless client will be connected to the Router or Access Point using WPS PIN method, then click on Finish.

Tags:

Mar 08

Step 1: Install the LucidLink server software on your computer.

Step 2: Click on Configure Access Point and select the Manufacturer and Model (D-Link, DWL-2100AP, DWL-2000AP) from the drop-down menu. Click Next.

dwl-2100ap-LucidLink1

Step 3: Once the Access Point is detected, you can change the IP address and password of the Access Point. To change the IP address, type it in the field next to IP Address. To change the password type it next to Password and then re-type it next to Confirm Password. Click Next.

dwl-2100ap-LucidLink2

Step 4: Next to Network Name enter your SSID (Service Set Identifier), and select the security method (Maximum Security or Maximum Compatibility) using the radio buttons below Choose The Security Method. Click Configure Access Point.

Note: If you select Maximum Security (WPA) the Shared Secret must be a minimum of 8 characters.

dwl-2100ap-LucidLink3

Step 5: Please wait while LucidLink completes the configuration process with the Access Point. This will take about 3-5 minutes. Do not disconnect the Ethernet cable or power cycle the unit during this process. If directly connected onto the Access Point, the Local area network status will switch between disconnected and connected. This is normal.

Step 6: Click Settings and enter a shared secret password next to Shared Secret. Also, enter your identification and contact information. To launch the LucidLink Management Console when Windows starts click the check box next to Automatically open the LucidLink Management Console whenever Windows starts. Click Save Settings to finish setup.

dwl-2100ap-LucidLink4

Note: The shared secret configured on the server must match the Shared Secret configured on every Access Point that communicates with the server. Configure the Shared Secret in the web-based configurations of the Access Points.

Tags: ,



 
Prev 1 2 3 ... 18 19 20 21 22 23 24 25 26 27 28 Next
css.php