Note:Do NOT upgrade firmware on any D-Link product over a wireless connection. Failure of the device may result. Use only hard-wired network connections.

Attention:

This firmware is engineered for North American products only.Using this firmware on a device outside of North America will void your warranty and may render the device unusable.

Please contact the D-Link office in your region for firmware updates that are compatible with your D-Link product.

Revision Info:

¤ Added: More help description for Advanced DNS feature.
¤ Added: Schedule feature supports 12 and 24 hour format.

Version:1.23NA

Download Site:

ftp://ftp.dlink.com/Gateway/dgl4500/firmware/dgl4500_FW_123NA.zip

1.Do NOT upgrade firmware on any D-Link product over a wireless connection. Failure of the device may result. Use only hard-wired network connections.

2.This firmware is engineered for North American products only.Using this firmware on a device outside of North America will void your warranty and may render the device unusable.

Firmware Version: 2.03NA

Firmware Date:7/07/2011

Revision Info:

¤ Address an issue with some Sony TV’s connecting to the router in n mode with security enabled.
¤ AdvanceDNS default enable.
¤ TOOLS DDNS add IPv6 DDNS.
¤ Support DNSSL (RFC6106).
¤ Support D-Link Router IPv6 Specification v1.16R.
¤ Add status IPv6 routing table.

Download Site:

ftp://ftp.dlink.com/Gateway/dir655_revB/Firmware/dir655_revB_FW_203NA.zip

Firmware: v1.01
Hardware: A1

Problems Resolved:

1. Fix wrong WAN port position picture in wizard setup.
2. Fix syslog function
3. DCS-5220 IPCAM WPA/WPA2 IOT issue.

Enhancements:

1. IPv6 NTP server default is support.
2. Ipv6 NTP feature
3. Add QoS uplink/downlink list for user choice.

Uplink Speed :128K/256K/384K/512K/1M/2M/3M/5M/10M/20M
Downlink Speed : 1M//2M/3M/8M/10M/12M/16M/40M/50M/100M

Download Now:

ftp://ftp.dlink.com/Gateway/dir645/Firmware/dir645_FW_101.zip

Make sure you do not plug any USB devices in the hub during hub installation. In most cases, Windows is asking for drivers for devices plugged into the hub, not the hub itself.

The driver for this USB hub and all other D-Link USB hubs is part of the installed driver set for the USB controller on your computer. This means that the drivers are supplied (built-in) by the operating system. If you have been using USB devices on your computer the drivers are already installed. However, it is possible that your OS may request drivers when installing the hub. In that case you must point the installation wizard to the Windows CD. Since these drivers are supplied by the operating system, D-Link is not allowed to distribute these files. If you continue to have problems installing drivers for your USB controller, please contact Microsoft for assistance.

It is basically the same story with Macintosh. You can also get the USB drivers or a patch as the case may be from the Apple web site.

How computer start up with DSB-H4 attached

With the power adapter always on, when the PC is shut down and then restarted, some motherboards will not boot up.

Reasons: The USB 5V is being feedback, sinking to the motherboard.

Symptoms: Some motherboards will exhibit power LED staying on or HDD LED staying on. With 5Vs feeding back into the computer from the DSB-H4, the power good signal on the motherboard is always on. In some motherboard designs, a power good signal is delayed , so the motherboards will not boot up until the USB cable or power cable is removed from the DSB-H4. Some motherboards do not have this issue because the USB port has diode protection.

Fix: To fix the problem you will have to remove the power supply along with the USB cable and restart your computer. Once restarted you can then plug everything back in.

Step 2: The Download Firmware dialog box will appear. Click Browse.

Step 3: Browse to the location where the firmware was saved and click OK.

Note: Do not interrupt the firmware upgrade process.

Step 4: Click OK once you recieve the confirmation prompt.

Step 5: The firmware file will start transfering to the print server.

Step 6: After the file has been uploaded, the Status page in the print server will reflect the version of the file that was just uploaded (in this example a DP-311U is used).

WDA-1320
WDA-2320
WNA-1330
WNA-2330
WUA-1340
WUA-2340
DWA-542
DWA-552
DWA-556
DWA-642
DWA-643
DWA-645
DWA-652
DFE-538TX (Canada Only)
DGE-530T
DGE-550SX
DGE-560T

DI-604 Firmware Download:

site: ftp://ftp.dlink.com/Gateway/di604_revE1/Firmware/di604_revE_firmware_353.bin

Version:3.53

Date:4/24/2007

Revision Info:

¤ Updated DDNS screen and request.
¤ Updated PPPoE WAN settings.
¤ Applied minor Grammar corrections

1.How to upgrade the firmware on DI-604?

Step 1: Download the latest firmware.

Step 2: Once you´ve downloaded the firmware, open a web browser such as Internet Explorer or Netscape and enter the IP address of your router (192.168.0.1).

Step 3: Enter your username (admin) and your password (leave the field blank). Click OK to enter the web configuration for the device.

Step 4: Click on the Tools tab and then the Firmware button on the left side. Click on the Browse button and browse to the .bin (or .dlf) file you downloaded in Step 1. Highlight the file by clicking on it once and click Open.

Step 5: Click Apply. It may take a up to 30 seconds for the upgrade to complete. Click on the Continue button. The firmware is now upgraded.

Step 6: If you get a Page cannot be displayed or similar error after clicking Continue, close your browser and re-open it. Enter 192.168.0.1 and press Enter. You should now be prompted for your username (admin) and your password (leave blank).

2.How to upgrade the firmware on the D-Link DI-604 and the DI-614+ using a Macintosh computer?

Step 1. Create a Folder on the Desktop Screen:
From a blank spot the Desktop Screen, press and hold the Control key on the keyboard and click the mouse button. Release the Control key, click New Folder, and name it firmware.

Step 2. Retrieve Firmware from Website:
Click link below and download file to the folder created in step 1.

Step 3. Upgrade the Firmware:
A. From the Main Desktop Screen, launch Internet Explorer or Netscape.

B. Type 192.168.0.1 in the Address bar and click Go.

C. For the User ID, type admin and click OK.

D. Click Tools on the top and then click Firmware on the left side.

E. Click Browse>Desktop>firmware, double click di6xx_firmware_203.bin and click Apply. Wait for approx. 15 seconds or until the M2 light stops flashing on the DI-6xx unit then click Continue.

F. This takes you back to the Tools page. Check the Current Firmware Version on the Tools page to confirm that the firmware loaded successfully.

BENEFITS OF DUAL BAND

The D-Link® Xtreme N™ Dual Band Gigabit Router (DIR-825) uses dual band technology to support 2.4GHz & 5GHz wireless signals at the same time. This allows you to check e-mail and browse the Internet using the 2.4GHz band while simultaneously streaming High-Definition (HD) movies and other media on the 5GHz band. The DIR-825 is designed for users looking to get a true HD wireless connection that can handle multiple HD video streams throughout the house, while being backward compatible with existing 802.11g and 802.11a products.

SHAREPORT

D-Link has created SharePort™ technology to bring more flexibility to your network. With SharePort technology, you can connect a USB printer and share it throughout your network. You can also share a USB storage device, providing network storage for everyone to share*.

CONSERVES ENERGY

• Automatically powers down ports that have no link
• Budgets power output for different Ethernet cable lengths
• Includes wireless LAN scheduling, which can shut down your wireless network when not in use for further power savings
• Reduces energy consumption by using an Energy Star® qualified power adapter

PROTECTING THE ENVIRONMENT

• Complies with the European Union’s RoHS directive that restricts the use of certain hazardous materials
• Uses recyclable packaging to help reduce waste that goes into the environment

Firmware: 1.13NA

Date: 1/28/2010

Revision Info: ¤ Fixed: Correct HNAP issue.

¤ Fixed: DNS relay issue ( WAN Slowdown )

¤ Added: Advanced DNS descriptions

Download site:ftp://ftp.dlink.com/Gateway/dir825/Firmware/dir825_firmware_113NA.zip

See our latest product: WUA-1340

DWL-G122 Description

D-Link, the industry pioneer in wireless networking, introduces the DWL-G122 Wireless USB Adapter, part of the AirPlus™ G family of 802.11g wireless networking devices.

Using the DWL-G122 Wireless USB Adapter, you can now enable 802.11g wireless connectivity for your PC using the convenience and speed of a USB 2.0 interface**. Featuring the latest in wireless technology, the DWL-G122 delivers incredibly fast performance and industrywide compatibility. By adhering to the 802.11g wireless standard, the DWL-G122 is capable of streaming video and transferring large files across a wireless network.

The DWL-G122 Wireless USB Adapter includes an easy-to-use configuration that discovers available wireless networks wherever you go. The utility can also create detailed connectivity profiles to save your most frequently used networks. You can also enable support for WPA and 802.1x, for better data encryption and user authentication.

DWL-G122 Firmware Driver

Now the DWL-122 Driver Version is 1.13

Download website : ftp://ftp.dlink.com/Wireless/dwlg122/Drivers/dwlg122_driver_113.zip

Firmware : 1.Enter the D-Link TaiWan Website:http://tsd.dlink.com.tw 2.Select a D-Link models,You can find the firmware you want.

In a typical configuration of a DMZ for a small company, a separate computer (or host in network terms) requests from users to access private network of web sites or other undertaking is open to the public. The DMZ host then initiates sessions for these requests on the public.
can, however, is the DMZ host does not log in to the private network. You can only packets that were requested.

The public network users outside the company can access the DMZ host. The DMZ usually include information on Web pages, so that it can be covered with the outside world. However, the zone does not allow access to data from another company. When an external user in the DMZ hosts security, Web pages can be damaged, but no information about the society of those suspended. D-Link, a leading manufacturer of routers, a company that sells products for the creation of a demilitarized zone.