Apr 11

This article teach you how to switch D-Link Advanced Settings.

Step 1 Open a web browser and type the IP address of the switch in the address bar (default is 10.90.90.90). Press Enter.

Step 2 Both the default username and password are blank (nothing). Click OK.

Step 3 On the left side, click Configuration and then click Advanced Settings.

Step 4 Configure the following:

d-link_switch

• Serial Port Auto Logout – This setting automatically logs out a user connected to the console port after a specified amount of time. Select 2 Minutes, 5 Minutes, 10 Minutes, 15 Minutes, or Never using the drop-down list. The default setting is 10 Minutes.

• Serial Port Baud Rate – This setting is locked down to 115220 and cannot be changed. Users connecting to the console interface of the switch must use this baud rate.

• MAC Address Aging Time (10-1000000) – This field specifies the length of time a learned MAC Address will remain in the forwarding table without being accessed (that is, how long a learned MAC Address is allowed to remain idle). The default age-out time for the switch is 300 seconds. To change this, type in a different value representing the MAC address age-out time in seconds. The MAC Address Aging Time can be set to any value between 10 and 1,000,000 seconds.

IGMP Snooping – Select Enabled to enable this feature or Disabled to disable it using the drop-down list. Enabling IGMP snooping allows you to specify use of a multicast router only. IGMP Snooping for individual VLANs needs to be configured on the IGMP Snooping page in the IGMP folder.

• Multicast router Only – Select Enabled to support Multicast router only or Disabled to disable it using the drop-down list.

GVRP Status – Select Enabled to enable GVRP or Disabled to disable it using the drop-down list. GVRP allows the switch to exchange VLAN configuration with other GVRP enabled switches, prune unnecessary broadcast traffic and unknown unicast traffic, and dynamically create and manage VLANs on switches connected through 802.1Q trunk ports.

• Telnet Status – Select Enabled to enabled administration of the switch via Telnet or Disabled to disable it using the drop-down list. This feature is enabled by default.

• Telnet TCP Port Number (1-65535) – Enter the port number for administering the switch via Telnet. The default port is 23.

• Web Status – This indicates if web-based administration is enabled. Web-based administration is configured on the IP Address page in the Configuration folder. The standard port used for web-based administration is 80.

• RMON Status – Select Enabled to allow Remote Monitoring (RMON) of the switch or Disabled to disable it using the drop-down list.

• Link Aggregation Algorithm – This is the algorithm that the switch uses to balance the load across the ports that make up the port trunk group. Select MAC Source, MAC Destination, MAC Src & Dest, IP Source, IP Destination or IP Src & Dest using the drop-down list.

• Switch 802.1x – Select Enabled to enable 802.1x for MAC-based or Port-based 802.1x function or Disabled to disable it using the drop-down list. This feature is disabled by default. Port-based 802.1x function will base authentication only on the port number. MAC-based 802.1x function uses the port number and specified MAC address as configured in the 802.1x Initialize Ports menu.

• Auth. Protocol – Select Local Eap or Radius Eap using the drop-down list. The default setting is Radius Eap.

• HOL Prevention – Select Enabled to enable Head of Line (HOL) Protection or Disabled to disable it using the drop-down list.

• Jumbo Frame – Select Enabled to enable support for Jumbo Frames up to 9216 bytes or Disable to disable using the drop-down list.

• Syslog State – Select Enabled to enable Syslog State or Disabled to disable it using the drop-down list. The default setting is Disabled. With Syslog State enabled the switch can report activity to a Syslog server.

Step 5: Click Apply to save the settings.

Be Sociable, Share!

Tags: , ,

No Comments


(Required)
(Required, will not be published)

css.php