Apr 05

Network Configuration:

This setup consists of separating two networks by the creating two VLANS on the DSR Series Service Router. This example will use the following setup:

Network 1 – 192.168.10.0 /24 – Default

Network 2 – 192.168.20.0 /24 – VLAN20

Step 1 – Enter the web GUI interface of the DSR using its IP address in a web browser. In our example we have used the IP address of 192.168.10.1

DSR_Series_FW2_How_to_setup_Two_VLANS1

Accept any certificate warnings you may see, this is perfectly normal and safe

Step 2 – You should then be presented with the login page

DSR_Series_FW2_How_to_setup_Two_VLANS2

Username: admin

Password: admin

Click “Login”

Step 3 – Click on the following options to setup VLANS

Network > VLAN > VLAN Settings

DSR_Series_FW2_How_to_setup_Two_VLANS3

Step 4 – Here you must firstly enable VLAN then click “Save”

DSR_Series_FW2_How_to_setup_Two_VLANS4

Step 5 – Once saved, click “Add New VLAN”

DSR_Series_FW2_How_to_setup_Two_VLANS5

VLAN IP: 20
Name: VLAN20
Capital Portal: Off
Activate InterVLAN Routing: Off
(InterVLAN Routing can stay “Off” this way there is no way that both networks will see each other
Multi VLAN Subnet: 192.168.20.1
Subnet Mask: 255.255.255.0

Step 5 – Click on the option “DHCP Server”

DSR_Series_FW2_How_to_setup_Two_VLANS6

Domain Name:
DHCP_VLAN20

Starting IP Address: 192.168.20.2

Ending IP Address: 192.168.20.254

Default Gateway: 192.168.20.1

Primary DNS Server: 8.8.8.8

Secondary DNS Server: 8.8.4.4.

Lease Time: 24

LAN Proxy: On (Default)

If you have a DHCP available for this new subnet, then click “DHCP Relay” and configure according to this network requirements. Once done, click “Save”

Within our example, we have used VLANID 20 for network 192.168.20.0/24. After clicking on “Save” our second VLAN will have been created

DSR_Series_FW2_How_to_setup_Two_VLANS7

Step 6 – The next step is to associate the VLAN with a port or certain ports. We will associate with Port 4

DSR_Series_FW2_How_to_setup_Two_VLANS8

Network > VLAN > Port VLAN

DSR_Series_FW2_How_to_setup_Two_VLANS9

Step 7
– In our example we are going to associate VLAN20 to Port 4. To do this, place the mouse over Port 4 and Right-Click then click on “Edit”

DSR_Series_FW2_How_to_setup_Two_VLANS10

Step 8 – Once clicked on “Edit”, we will need to select “Mode” as “Access” with a PVID 20 (Step 5)

DSR_Series_FW2_How_to_setup_Two_VLANS11

Once done, click on “Save”

DSR_Series_FW2_How_to_setup_Two_VLANS12

NOTE: If you intend to connect a non-manageable switch to port 4 which doesn’t support VLANS then the mode “Access” is correct.

However, if you are planning to connect a manageable switch that does understand VLANS then you will need to select “Trunk” and VLAN Membership 20

DSR_Series_FW2_How_to_setup_Two_VLANS13

Be Sociable, Share!

Tags: ,

No Comments


(Required)
(Required, will not be published)

css.php