D-Link Blog Home

To configure your network settings:

Static IP Client:

You may obtain a static or fixed IP address and other network information from your network administrator for your camera. A static IP address will ease you for accessing your camera in the future.

IP Address: The fixed IP address Subnet Mask: The default value is “255.255.255.0.” Used to determine if the destination is the same subnet.

Default Gateway: The gateway used to forward frames to destinations in a different subnet. Invalid gateway settings may cause the failure of transmissions to a different subnet.

Primary DNS: Primary domain name server that translates names to IP addresses.

Secondary DNS: Secondary domain name server to backup the Primary DNS.

DHCP:

Select this connection if you have a DHCP server running on your network and would like a dynamic IP address to be updated to your camera automatically.

PPPoE Settings:

PPPoE settings:If you are using a PPPoE connection, enable it and enter the User Name and Password for your PPPoE account. You can get this information from your Internet service provider (ISP).

Port Settings:

You may configure a Second HTTP port that will allow you to connect to the camera via a standard web browser. The port can be set to a number other than the default TCP ports 80. A corresponding port must be opened on the router. For example, if the port is changed to 1010, users must type http://192.168.0.100:1010 instead of only “http://192.168.0.100”.

UPnP Settings:

Enable this setting to configure your camera as an UPnP device in the network.

Tags: DCS-930L, Network camera

Step 1: Insert the DBT-120 Wireless Bluetooth 2.0 USB Adapter into you Vista / Windows 7 PC.

Step 2: Reboot the computer. Waiting for Vista / Windows 7 to recognize the new hardware. Once it prompts you to locate the driver. Click Locate And Install Driver Software (Recommended).

Step 3: Allow Vista / Windows 7 to locate and install drivers from the Internet.

Step 4: After the drivers are installed, Vista / Windows 7 will tell you the device has installed properly and is ready to use.

The D-Link DBT-120 is now installed and ready to use in Vista / Windows 7.

Tags: Bluetooth, DBT-120

Some people forget the D-Link DAP-1522 password,This article teaches how do reset on DAP-1522.

Step 1: With the unit on, place a paper clip into the hole on the back on the unit labeled Reset.

Step 2: Hold paper clip down for 10 seconds and release.

Note: Do not repower unit during this procedure.

Step 3: The unit will reboot on its own. Once the WLAN light stops blinking, the unit is reset.

Resetting the D-Link DAP-1522 will change all settings back to factory defaults.

Note: The factory defaults name is admin, and password is blank(nothing).

Tags: DAP-1522, factory defaults, forget password

Set or change the administrative password on D-Link DAP-1555/1522:

Step 1: Open a web browser and entering the IP address 192.168.0.50. Press Enter.

Step 2: The default password is blank (nothing). Click Log In.

Step 3: Click Maintenace at the top.

Step 4: In the Admin section enter your new password next to Password and enter it again next to Verify Password.

Step 5: Click Save Settings at the top to save the new password.

Tags: DAP-1522, default password

This article will teach you how to set up D-Link Wireless N Network Camera and WPS setup,DCS-930L As an Example.

Quick Installation:

Step 1:

Connect the included Ethernet cable to the network cable connector located on the bottom panel of the DCS-930L and attach it to the network.

Step 2:

Attach the external power supply to the DC power input connector located on the bottom panel of the DCS-930L and connect it to your wall outlet or power strip. Power is confirmed when the green LED Power Indicator located below the lens is lit.

Step 3:

Insert the DCS-930L Driver CD in the CD-ROM drive. If the CD Autorun function does not automatically start on your computer, go to Start > Run. In the run box type D:\autorun.exe (where D: represents the drive letter of your CD-ROM drive) and click OK. When the autorun screen appears, click Install and follow the on-screen instructions.

Step 4:

Click on the Start button to start the wizard.

WPS Setup:

Alternatively, you may create a WPS connection if your router or access point supports WPS. To create a WPS connection:

Step 1:

Press and hold the WPS button on the side of the camera for three seconds. The blue WPS status LED above the button will blink.

Step 2:

Press the WPS button on your wireless router or access point within 60 seconds. On some routers, you may need to log into the web interface and then click an onscreen button to activate the WPS feature. If you are not sure where the WPS button is on your router or access point, please refer to your router’s user manual. The DCS-930L will automatically create a wireless connection to your router. While connecting, the green LED will flash and your camera will reboot.

Tags: DCS-930L, Network camera, WPS