Jan 07

The D-Link DIR-510L can be used as a portable charger to recharge your mobile devices on the go, including high-powered devices such as tablets.

Step 1: Slide the ON/OFF/CHARGER switch on the top of the DIR-510L to CHARGER.

Step 2: Plug your device into the USB port of the D-Link DIR-510L. Check your device to make sure it is now charging.

Note: If the battery LED is red, you will need to charge the DIR-510L. Actual usable capacity may vary depending on charging conditions.

Tags: ,

Jan 07

Solid White

– Your COVR system is working properly.

 

Flashing White 

– If any of your COVR points are flashing white, it means that it is getting a weak signal to another COVR point. Try moving the COVR point closer to COVR Point A.

 

Flashing Orange on COVR-Point A

– If your COVR Point A is flashing Orange, this means that it is not getting a connection to the internet.

 

– DSL/PPPoE Internet Users

– If using a DSL/PPPoE internet service, verify the username and password you entered is correct.

 

– Cable Internet Users

– If using a cable internet service, try powering off your modem for 30 seconds (removing any backup battery if applicable) and powering it back on.

 

Flashing Orange on other Covr Points (not A)

– If any of your COVR extenders are flashing orange (NOT Covr point A), its means it is not in range or could not connect to another COVR point. Try moving the COVR extender closer to another COVR point.

 

Solid Red 

– Your COVR points will be solid red during boot up (powered on). Boot up can take anywhere from 2-3 minutes.

 

Flashing Red 

– Flashing Red indicates that there is a problem with the device. If flashing red, please contact our tech support team at 1-877-453-5465 (USA only) or via email at support.dlink.com/covr-c1203-us.

Tags: ,

Jan 07

How to use the rescue mode of a ASUS router RT-AC66U?

Example: RT-AC66U

Please launch the browser and go to the Driver & Tools page in [RT-AC66U] on the  ASUS Official Website. Please follow the steps in the screenshot below to find the device firmware.

 (1) Download the latest firmware.

  1. Click [Support]
  2. Click [Driver & Utility]
  3. Click [BIOS & FIRMWARE]
  4. Find the latest firmware
  5. Click [DOWNLOAD] to download

(2) Download and install the utility

  1. Click [Support]
  2. Click [Driver & Utility]
  3. Click [Driver & Tools]
  4. Select OS
  5. Click [EXPAND ALL +]
  6. Find ASUS Firmware Restoration utility
  7. Click [DOWNLOAD] to download

8. Find the ZIP file and unzip it.

 9. Double click the file to install.

On your Router

Press the power button to turn off the router.

Press and hold the button [RESTORE] for about 5 seconds.

While still pressing the [RESTORE] button, press the power button to turn on the Wireless Router

If the power light is flashing-slow, this means the wireless router is in Rescue Mode.

Computer:


Click [Start][Control panel]→ [network and Internet][Network and Sharing Center][Change adapter settings] → [LAN]→ Click[Properties]

Click [Internet protocol version 4 (TCP/IPv4)]→Click [Properties]
Modify the content of [Internet Protocol Version 4 (TCP/IPv4) Properties] as shown below:

The following IP address : IP address:192.168.1.10 / Subnet mask:255.255.255.0 → click [OK]


Click[Start][All programs][ASUS Utility][Wireless Router][Firmware Restoration]



At the [Firmware Restoration] window, click [Browse] and choose the latest firmware which you had downloaded.

Click [Upload]

Please wait for 60 seconds

Click [Close] when the Status message shows [Successfully recovered the system. Please wait for system to reboot].

On your Router:

Steady power light indicates the setting procedure of Rescue Mode has been completed successfully.

※ NOTE: Please choose [Obtain an IP address automatically] after the procedure is completed.

Tags: , ,

Jan 07

How to set up Virtual Server and Port Forwarding on ASUS Wireless Router?


1. Router WAN IP address – This is the IP address provided by your ISP to access the Internet.  This WAN IP address will also be used to access the PC providing the service.  In this example, the Router WAN IP address is “123.123.123.123”.

2. Router LAN IP address – The default IP address of your ASUS router is “192.168.1.1”.

3. For personal use – This computer has been assigned a LAN IP address of “192.168.1.130” by the router.  This PC does not provide any network service.

4. Server LAN IP address – This PC is assigned a static LAN IP Address of “192.168.1.103”.

This is the server PC that provides network services to other clients on the Internet.  Port forwarding will be applied to this PC.

To set up Port Forwarding:

Launch a browser and access router settings by keying in LAN IP address or http://router.asus.com on the address bar.

Click “WAN” on the Advanced Settings menu on the left panel.

Click the “Virtual Server/Port Forwarding” tab.

To set up Port Forwarding for a FTP server:

Before setting up port forwarding for a FTP server, a PC on the Internet cannot connect to the FTP server.

Under the Basic Config section, select “FTP” from the “Famous Server List” item.  Input a port or port range for the FTP server and select the Local IP.

In this example, the Server LAN IP address is “192.168.1.103“.

Click on “Edit” and then click on “Apply“.

Note:  Do not use the port range 20:21 for an FTP server if the AiDisk service on the router has been enabled. 

 

The FTP server is now running using the following settings:
Host: 123.123.123.123
Port: 2021

Source Target 

Rules that only the IP address can be forwarded for the match port

For Source IP address, you can:

  • (a)   Leave it empty. Unspecified, that is, any source IP can.
  • (b)   Enter a specific IP address, such as “192.168.122.1”
  • (c)    Enter IP address within one subnet or the same IP pool, such as “192.168.123.*”, or “192.168.*.*” or “*.*.*.*”

To check if Port Forwarding has successfully been configured for a FTP server:

  1. Ensure that your FTP server is set up and running.
  2. You will need a PC outside your LAN but has Internet access (hereafter referred to as “Internet PC”).  This PC should not be connected to the ASUS router in any way.
  3. On the Internet PC, use the router’s WAN IP to access the FTP server using a FTP application or FTP browser.  If port forwarding has been successful, you should be able to access the files on the FTP server.

 

To set up port forwarding for a HTTP server:

Before setting up port forwarding for an HTTP server, a PC on the Internet cannot connect to your server/PC via HTTP.

Under the Basic Config section, select “HTTP” from the “Famous Server List” item.  Input a port or port range for the HTTP server and select the Local IP.

In this example, the Server LAN IP address is “192.168.1.103“.

Click on “Edit” and then click on “Apply“.

The HTTP server is now running using the following settings:
Host: 123.123.123.123
Port: 80

Source Target: Rules that only the IP address can be forwarded for the match port

For Source IP address, you can:

  • (a)   Leave it empty. Unspecified, that is, any source IP can.
  • (b)   Enter a specific IP address, such as “192.168.122.1”
  • (c)    Enter IP address within one subnet or the same IP pool, such as “192.168.123.*”, or “192.168.*.*” or “*.*.*.*”

 

To check if port forwarding has successfully been configured for an HTTP server:

  1. Ensure that your HTTP server is set up and running.
  2. You will need a PC outside your LAN but has Internet access (hereafter referred to as “Internet PC”).  This PC should not be connected to the ASUS router in any way.
  3. On the Internet PC, launch a web browser and key in the router’s WAN IP address on the address bar.  If port forwarding has been successful, you should be able to access the web page provided by the HTTP server.

**If you want to forward a port range, for example 10200:10300, to a PC which is using the same port range, enter the service name, port range, and local IP address, but leave the local port blank.

Tags: , ,

Jan 06

How to set up an Internet Connection on ASUS Wireless WAN

 

1. Enter the IP address of your device in the browser, followed by your username and password to login to your ASUS networking device.

ASUS Wireless Routers use a web-based user interface that allows you to configure the router by any web browser, such as Internet Explorer, Mozilla Firefox, Apple Safari, or Google Chrome.

 

 

2. Click [Quick Internet Setup]

The Quick Internet Setup function guides you to quickly set up your Internet connection.

The wireless router automatically detects if your ISP connection type is Automatic IP, Static IP, PPPoE, PPTP and L2TP. Key in the necessary information for your ISP connection type.

IMPORTANT: Obtain the necessary information from your ISP about the Internet connection type.

 

 

3. If you need detailed setup information, go to the WAN- Internet Connection.

 

4. There are 5 WAN connections to choose from : Automatic IP, Static IP. PPPoE, PPTP, L2TP.

Automatic IP

Enable WAN: Enable and disable WAN. Under some connection types, you can get a new IP address by using Enable and Disable WAN.

Enable NAT: NAT(Network Address Translation) is a process used in routers to replace the address information of network packets with new address information. Typical applications for NAT is for routers which connect to LAN with the WAN. In LAN, every network device had a private IP (LAN IP) but there’s only one public IP (WAN IP). To grant internet access to the network devices, the router replaces the private IP address of the sender with its own public IP address in all outgoing data packets. The router saves all necessary information in a table (NAT table) so that incoming data packets can then be assigned to the correct network device.

Enable UPnP: UPnP(Universal Plug and Play) allows several devices(routers, televisions, stereo systems, game consoles, cellular phone) to be controlled via an IP-based network with or without a central control through a gateway.

Connect to DNS Server automatically: Allows this router to get the DNS IP address from the ISP automatically.

Authentication: This item may be specified by some ISPs. Check with your ISP and fill them in if required.

Host Name: You can provide a host name for your router. It’s usually requested by your ISP.

MAC Address: MAC(Media Access Control) address is a unique identifier that identifies your computer or device in the network. ISPs monitor the MAC addresses of devices that connect to their services, and would disallow Internet Connection for new MAC addresses. To fix this issue, you can do either of the following:
* Contact your ISP and request to update the MAC address associated with your ISP subscription.
* Clone or change the MAC address of the new device to match the MAC address of the original device.

DHCP query frequency: Some Internet Service Providers block MAC addresses if the device makes DHCP queries too often. To prevent this, change the DHCP query frequency.
In the default Aggressive mode, if the router does not get a response from the ISP, it sends another query after 20 seconds and then makes three more attempts.
In Normal mode, if the router doesn’t get a response from the ISP, it makes a second query after 120 seconds and then makes two more attempts.

 

Static IP

Enable WAN: Enable and disable WAN. Under some connection type, you can get a new IP address by enable and disable WAN.

Enable NAT: NAT(Network Address Translation) is a process used in routers to replace the address information of network packet with new address information. Typical applications for NAT is router which connect to LAN with the WAN. In LAN, every network devices had a private IP(LAN IP) but there’s only one public IP(WAN IP). To grant the network devices access to internet, the router replaces the private IP address of the sender with its own public IP address in all outgoing data packets. The router saves all necessary information in a table(NAT table) so that incoming data packets can then be assigned to the correct network device.

Enable UPnP: UPnP(Universal Plug and Play) allows several devices(routers, televisions, stereo systems, game consoles, cellular phone) to be controlled via an IP-based network with or without a central control through a gateway.

IP Address: If your WAN connection requires a static IP address, key in the IP address in this field.

Subnet Mask: If your WAN connection requires a static IP address, key in the subnet mask in this field.

Default Gateway: If your WAN connection requires a static IP address, key in the gateway IP address in this field.

DNS Server: This field indicates the IP address of DNS that the router contacts to.

Authentication: Some Internet Service Providers block MAC addresses if the device makes DHCP queries too often. To prevent this, change the DHCP query frequency. In the default Aggressive mode, if router does not get a response from the ISP, it sends another query after 20 seconds and makes three more attempts. In Normal mode, if router doesn’t get a response from the ISP, it makes a second query after 120 seconds and makes two more attempts.

Host Name: You can provide a host name for your router. It’s usually requested by your ISP.

MAC Address: MAC(Media Access Control) address is a unique identifier that identifies your computer or device in the network. ISPs monitor the MAC addresses of devices that connect to their services, and would disallow Internet Connection for new MAC addresses. To fix this issue, you can do either of the following:
* Contact your ISP and request to update the MAC address associated with your ISP subscription.
* Clone or change the MAC address of the new device to match the MAC address of the original device.

 

PPPoE

Enable WAN: Enable and disable WAN. Under some connection type, you can get a new IP address by enable and disable WAN.

Enable NAT: NAT(Network Address Translation) is a process used in routers to replace the address information of network packet with new address information. Typical applications for NAT is router which connect to LAN with the WAN. In LAN, every network devices had a private IP(LAN IP) but there’s only one public IP(WAN IP). To grant the network devices access to internet, the router replaces the private IP address of the sender with its own public IP address in all outgoing data packets. The router saves all necessary information in a table(NAT table) so that incoming data packets can then be assigned to the correct network device.

Enable UPnP: UPnP(Universal Plug and Play) allows several devices(routers, televisions, stereo systems, game consoles, cellular phone) to be controlled via an IP-based network with or without a central control through a gateway.

Get the WAN IP automatically: Allows the router to get the WAN IP address from the ISP automatically.

Connect to DNS Server automatically: Allows this router to get the DNS IP address from the ISP automatically.

User Name: Fill-in the information which ISP provided.

Password: Fill-in the information which ISP provided.

Idle Disconnect Time in seconds: Disconnect after time of inactivity (in seconds): This field is optional and allows you to configure to terminate your ISP connection after a specified period of time. A value of zero allows infinite idle time.

MTU: The Maximum Transmission Unit(MTU) of PPPoE packet. The default value is 1492. Change this value only if your ISP requires it.

MRU: The Maximum Receive Unit(MRU) of PPPoE packet. The default value is 1492. Change this value only if your ISP requires it.

Service Name: This field is optional and may be specified by some ISPs. Check with your ISP and fill them in if required.

Access Concentrator Name: This field is optional and may be specified by some ISPs. Check with your ISP and fill them in if required.

Additional pppd options: This item may be specified by some ISPs. Check with your ISP and fill them in if required.

Enable VPN + DHCP Connection: Decied you want to enable VPN and DHCP connection or not.

Host Name: You can provide a host name for your router. It’s usually requested by your ISP.

MAC Address: MAC(Media Access Control) address is a unique identifier that identifies your computer or device in the network. ISPs monitor the MAC addresses of devices that connect to their services, and would disallow Internet Connection for new MAC addresses. To fix this issue, you can do either of the following:
* Contact your ISP and request to update the MAC address associated with your ISP subscription.
* Clone or change the MAC address of the new device to match the MAC address of the original device.

 

PPTP

Enable WAN: Enable and disable WAN. Under some connection type, you can get a new IP address by enable and disable WAN.

Enable NAT: NAT(Network Address Translation) is a process used in routers to replace the address information of network packet with new address information. Typical applications for NAT is router which connect to LAN with the WAN. In LAN, every network devices had a private IP(LAN IP) but there’s only one public IP(WAN IP). To grant the network devices access to internet, the router replaces the private IP address of the sender with its own public IP address in all outgoing data packets. The router saves all necessary information in a table(NAT table) so that incoming data packets can then be assigned to the correct network device.

Enable UPnP: UPnP(Universal Plug and Play) allows several devices(routers, televisions, stereo systems, game consoles, cellular phone) to be controlled via an IP-based network with or without a central control through a gateway.

Get the WAN IP automatically: Allows the router to get the WAN IP address from the ISP automatically.

IP Address: If your WAN connection requires a static IP address, key in the IP address in this field.

Subnet Mask: If your WAN connection requires a static IP address, key in the subnet mask in this field.

Default Gateway: If your WAN connection requires a static IP address, key in the gateway IP address in this field.

Connect to DNS Server automatically: Allows this router to get the DNS IP address from the ISP automatically.

DNS Server: This field indicates the IP address of DNS that the router contacts to.

User Name: Fill-in the information which ISP provided. This filed is only available when setting the WAN Connection Type as USB Modem, PPPoE, PPTP or L2TP.

Password: Fill-in the information which ISP provided. This field is only available when setting WAN Connection Type as PPPoE.

Idle Disconnect Time in seconds: Disconnect after time of inactivity (in seconds): This field is optional and allows you to configure to terminate your ISP connection after a specified period of time. A value of zero allows infinite idle time.

PPTP Options: This item may be specified by some ISPs. Check with your ISP and fill them in if required.

Additional pppd options: This item may be specified by some ISPs. Check with your ISP and fill them in if required.

VPN Server: If your WAN connection type is PPTP or L2TP, please enter the server name or server IP of the VPN Server.

Host Name: You can provide a host name for your router. It’s usually requested by your ISP.

MAC Address: MAC(Media Access Control) address is a unique identifier that identifies your computer or device in the network. ISPs monitor the MAC addresses of devices that connect to their services, and would disallow Internet Connection for new MAC addresses. To fix this issue, you can do either of the following:
* Contact your ISP and request to update the MAC address associated with your ISP subscription.
* Clone or change the MAC address of the new device to match the MAC address of the original device.

 

L2TP

Enable WAN: Enable and disable WAN. Under some connection type, you can get a new IP address by enable and disable WAN.

Enable NAT: NAT(Network Address Translation) is a process used in routers to replace the address information of network packet with new address information. Typical applications for NAT is router which connect to LAN with the WAN. In LAN, every network devices had a private IP(LAN IP) but there’s only one public IP(WAN IP). To grant the network devices access to internet, the router replaces the private IP address of the sender with its own public IP address in all outgoing data packets. The router saves all necessary information in a table(NAT table) so that incoming data packets can then be assigned to the correct network device.

Enable UPnP: UPnP(Universal Plug and Play) allows several devices(routers, televisions, stereo systems, game consoles, cellular phone) to be controlled via an IP-based network with or without a central control through a gateway.

Get the WAN IP automatically: Allows the router to get the WAN IP address from the ISP automatically.

IP Address: If your WAN connection requires a static IP address, key in the IP address in this field.

Subnet Mask: If your WAN connection requires a static IP address, key in the subnet mask in this field.

Default Gateway: If your WAN connection requires a static IP address, key in the gateway IP address in this field.

Connect to DNS Server automatically: Allows this router to get the DNS IP address from the ISP automatically.

DNS Server: This field indicates the IP address of DNS that the router contacts to.

User Name: Fill-in the information which ISP provided. This filed is only available when setting the WAN Connection Type as USB Modem, PPPoE, PPTP or L2TP.

Password: Fill-in the information which ISP provided. This field is only available when setting WAN Connection Type as PPPoE.

Additional pppd options: This item may be specified by some ISPs. Check with your ISP and fill them in if required.

VPN Server: If your WAN connection type is PPTP or L2TP, please enter the server name or server IP of the VPN Server.

Host Name: You can provide a host name for your router. It’s usually requested by your ISP.

MAC Address: MAC(Media Access Control) address is a unique identifier that identifies your computer or device in the network. ISPs monitor the MAC addresses of devices that connect to their services, and would disallow Internet Connection for new MAC addresses. To fix this issue, you can do either of the following:
* Contact your ISP and request to update the MAC address associated with your ISP subscription.
* Clone or change the MAC address of the new device to match the MAC address of the original device.

Tags: , ,



 
Prev 1 2 3 4 5 6 7 8 9 10 ... 185 186 187 Next
css.php