Jan 05

 Installing in Access Point Mode

Plug the supplied power adapter into your DAP-1665 and connect it to the outlet or surge protector. Press thePower button on the back of the device. Verify that the Power LED is lit.

A10717_image1

  1. Attach one end of the included Ethernet cable to the LAN port on the back of the D-Link DAP-1665, and the other end into the Ethernet port on your wireless router.A10717_image2
  2. From the computer connected to your wireless router, open a web browser (e.g., Internet Explorer, Firefox, Safari, or Chrome) and enter http://dlinkap.local./. Windows XP users can enter http://dlinkap. Use the Setup Wizard to configure your AP.A10717_image3
  3. At the login screen, select Admin from the User Name drop-down menu and leave the password blank. Click Log In to continue.A10717_image4
  4. Click Launch Wireless Setup Wizard and you will be guided through the steps required to get your access point up and running.A10717_image5
  5. You will see the welcome screen for the Wi-Fi Connection Setup Wizard. Click Next to continue.A10717_image6
  6. Select Access Point from the Wireless Mode drop-down menu. Click Next to continue.A10717_image7
  7. Enter a 2.4Ghz and 5GHz Wi-Fi Network Name and Wi-Fi Password. Click Next to continue.A10717_image8
  8. When setup is complete, make a note of your settings and click Save. The DAP-1665 will reboot.

    A10717_image9
Your setup is complete. 

Tags: ,

Dec 31

 Installation Repeater Mode

Find an available power outlet near your wireless router. Plug the supplied power adapter into your DAP-1665 and connect it to the outlet or to a surge protector. Press the Power switch on the back of the device. Verify that the Power LED is lit.

Note:
If your router does not have WPS, skip  to the section Configure Using a Web Browser.


A10718_image1

  • Press the WPS button on your existing wireless router or AP.
    Note: Usually the WPS LED will start to blink. If necessary, check your router’s user manual for more information.

    A10718_image2
  • Within one minute, press and hold the WPS button on the side of the DAP-1665 for about one second. The WPS LED will blink. When the Security LED becomes a solid green, it means wireless security is enabled. Allow up to two minutes for the WPS process to complete.
  • A10718_image3

    N
    ote: For optimal performance using Repeater Mode, place your DAP-1665 in between your router and your dead zone, making sure it’s placed in a location where the signal is still strong.

 

A10718_image4

Connect Your Wireless Devices

From your wireless device go to the Wireless Utility to display the available wireless networks and select the Wi-Fi Network Name (SSID) that is located on your configuration card (ex: dlink-a8fa). Then, enter the Wi-Fi password which is also located on your configuration card. (ex: akbdj19368).

A10718_image5

  • Your device is now connected to the DAP-1665 and can connect to your wireless router.

 

 

Your setup is complete! 
Configure Using a Web Browser
  1. Find an available power outlet near your wireless router. Plug the supplied power adapter into your DAP-1665 and connect it to the outlet or to a surge protector. Press the Power switch on the back of the device. Verify that the Power LED is lit.A10718_image11
  2. From the computer connected to your wireless router, open a web browser (e.g., Internet Explorer, Firefox, Safari, or Chrome). Enter http://dlinkap.local./. Windows XP users can enter http://dlinkap. Use the Setup Wizard to configure your AP manually.
  3. A10718_image6

 

NOTE: The default IP address is 192.168.0.50. Once the DAP-1665 (in Repeater or Client mode) connects to your router, it will get assigned a new IP address based on your router/network’s DHCP settings. You will need to log in to your router and view the DHCP table to see what IP address was assigned to the DAP-1665. The MAC address is printed on the label on the bottom of the device.

Tags: ,

css.php