Nov 15

Step 1: Log into the unit by entering the switch’s IP address in a web browser. The default username is adminwith no password.

A10429_image1

Step2: Choose the menu L2 Features->VLAN->Static VLAN on the left hand side.

A10429_image2

Step 3: In the row for VID 1 click the Modify button. Switch any port that will be untagged on your new VLAN to the None radio button for that port. Click Apply when finished.

A10429_image3

Step 4: Click the Show All Static VLAN Entries link. Click on the Add button. Enter your desired VID and VLAN Name for your new VLAN. Any port you wish to be a member should have its Egress radio button selected. Untagged members require no further modification. Tagged members must also have the Tag check box checked. Hit Apply when finished.

A10429_image4

Step 5: Select the menu Save Services->Save Changes. Click the Save button.

A10429_image5

Tags: ,

Jul 06

D-Link DGS-3600 Layer 3 Gigabit Switch Include:DGS-3612,DGS-3620,DGS-3627,DGS-3650

1.IPv6 Ping Test

The following window is used to Ping an IPv6 address.

To view this window, click Administration > Ping Test > IPv6 Ping Test, as shown below:

DGS-3600-ipv6-1

This window allows the following parameters to be configured to ping an IPv6 address.

Parameter Description

Target IPv6 Address:Enter an IPv6 address to be pinged.

Interface:The Interface field is used for addresses on the link-local network. It is recommended that the user enter the specific interface for a link-local IPv6 address. For global IPv6 addresses, this field may be omitted.

Repeat Times:Enter the number of times desired to attempt to ping the IPv6 address configured in this window. Users may enter a number of times between 1and 255.

Size:Use this field to set the datagram size of the packet, or in essence, the number of bytes in each ping packet. Users may set a size between 1 and 6000 bytes. The default setting is 100 bytes.

Timeout:Select a timeout period between 1 and 99 seconds for this Ping message to reach its destination. If the packet fails to find the IPv6 address in this specified time, the Ping packet will be dropped.

Source IPv6 Address:Tick the check box and enter the source IPv6 address of the ping packets. If specified, the IPv6 address will be used as the packets’ source IPv6 address that ping6 sends to the remote host.

2.IPv6 Neighbor Settings

IPv6 neighbors are devices on the link-local network that have been detected as being IPv6 devices. These devices can forward packets and keep track of the reachability of routers, as well as if changes occur within link-layer addresses of nodes on the network or if identical unicast addresses are present on the local link. The following two windows are used to view IPv6 neighbors, and add or delete them from the Neighbor cache.

The following window is used to view and configure current IPv6 neighbors of the Switch.
To view this window, click Administration > IPv6 Neighbor > IPv6 Neighbor Settings, as shown below:

DGS-3600-ipv6-2

Interface Name:Enter the Interface Name of the device for which to search IPv6 neighbors. Click Find to begin the search.

Neighbor IPv6 Address:Enter the IPv6 address of the neighbor of the IPv6 device to be searched. Click Find to begin the search.

State:Users may also search by running state of the IPv6 neighbor. Tick the State check box and choose to search for Static IPv6 neighbors or Dynamic IPv6 neighbors. Click Find to begin the search.

Neighbor IPv6 Address:Displays the IPv6 address of the neighbor device.

State:Displays the running state of the corresponding IPv6 neighbor. The user may see six possible entries in this field, which are Incomplete, Stale, Probe, Reachable, Delay, or Static.

Link Layer MAC Address:Displays the MAC address of the corresponding IPv6 device.

Port:Displays which port learned the IPv6 address of the neighbor device.

Interface:Displays the interface name associated with this IPv6 address.

VID:Displays which VLAN learned the IPv6 address of the neighbor device.

Tags: , , ,

Aug 04

Step 1: Log into the unit by entering the switch’s IP address in a web browser. The default username is admin with no password.

dlink-LACPScreen2

Step 2: Select the L2 Features->Trunking->Link Aggregation menu on the left hand side.

dlink-LACPScreen

Step 3: Click the Add button. Enter in your desired Group ID. The type should be LACP. The State should be Enabled. Select your Master Port and check the box for every desired member of your LACP group including the master. Hit the Save button when finished.

dlink-LACPScreen3

Tags: , ,

Feb 06

Step 1: Log into the unit by entering the switch’s IP address in a web browser. The default username is admin with no password.

DGS-3600-login

Step2: Choose the menu L2 Features->VLAN->Static VLAN on the left hand side.

DGS-3600-login2

Step 3: In the row for VID 1 click the Modify button. Switch any port that will be untagged on your new VLAN to the None radio button for that port. Click Apply when finished.

DGS-3600-login3

Step 4: Click the Show All Static VLAN Entries link. Click on the Add button. Enter your desired VID and VLAN Name for your new VLAN. Any port you wish to be a member should have its Egress radio button selected. Untagged members require no further modification. Tagged members must also have the Tag check box checked. Hit Apply when finished.

DGS-3600-login4

Step 5: Select the menu Save Services->Save Changes. Click the Save button.

DGS-3600-login5

Tags: ,

css.php