Nov 03

Configuration of DI-824VUP Local Side

Step 1: Open your web browser and type in the IP address of the router (192.168.0.1 by default). Enter the username (admin by default) and password (blank by default), and then click OK.

Step 2: Select the Home tab and click VPN on the left side.

Step 3: Configure the VPN Settings as followed:

  • VPN: check to enable
  • NetBIOS broadcast: leave uncheck
  • Max. number of tunnels: enter the maximum number of VPN tunnels that can be established
  • ID 1: enter a name to identify the VPN tunnel under Tunnel Name and select IKE under Method.

Click Apply.

A10505_image1

Step 4: Select Home and click on VPN to go back to the previous page and select More next to Method.

A10505_image2

Step 5: Configure the VPN tunnel as followed:

  • Name: should already be entered from step 3
  • Aggressive Mode: leave unchecked
  • Local Subnet: enter the local subnet (192.168.1.0 in this example)
  • Local Netmask: enter the local netmask (255.255.255.0 in this example)
  • Remote Subnet: enter the remote subnet (192.168.0.0 in this example)
  • Remote Netmask: enter the remote netmask(255.255.255.0 in this example)
  • Remote Gateway: enter the remote gateway
  • IKE Keep Alive(Ping IP Address): enter the default gateway of the remote location
  • Preshare Key: enter a key (The preshare key must be the same on both side.)

Click Apply.

A10505_image3

Step 6: Select Home, VPN, More and click on Select IKE Proposal.

A10505_image4

Step 7: Configure the IKE Proposal ID 1 as followed:

  • Proposal Name: enter a name as desired
  • DH Group: select Group 1
  • Encrypt algorithm: select 3DES
  • Auth algorithm: select SHA1
  • Life Time: select 28800
  • Life Time Unit: select Sec.
  • Proposal ID: use the dropdown list and select 1 and click Add to so that the name of the proposal appears in the IKE Proposal index.

Click Apply.

A10505_image5

Step 8: Select Home, VPN, More and click on Select IPSec Proposal.

A10505_image6

Step 9: Configure the IPSec Proposal ID 1 as followed:

  • Proposal Name: enter a name as desired
  • DH Group: select Group 1
  • Encap protocol: select ESP
  • Encrypt algorithm: select 3DES
  • Auth algorithm: select SHA1
  • Life Time: select 3600
  • Life Time Unit: select Sec.
  • Proposal ID: use the dropdown list and select 1 and click Add to so that the name of the proposal appears in the IPSec Proposal index.

Click Apply.

A10505_image7


Configuration of DI-824VUP Remote Side

Step 1: Open your web browser and type in the IP address of the router (192.168.0.1 by default). Enter the username (admin by default) and password (blank by default), and then click OK.

Step 2: Select the Home tab and click VPN on the left side.

Step 3: Configure the VPN Settings as followed:

  • VPN: check to enable
  • NetBIOS broadcast: leave uncheck
  • Max. number of tunnels: enter the maximum number of VPN tunnels that can be established
  • ID 1: enter a name to identify the VPN tunnel under Tunnel Name and select IKE under Method.

Click Apply.

A10505_image8

Step 4: Select Home and click on VPN to go back to the previous page and select More next to Method.

A10505_image9

Step 5: Configure the VPN tunnel as followed:

  • Name: should already be entered from step 3
  • Aggressive Mode: leave unchecked
  • Local Subnet: enter the local subnet (192.168.0.0 in this example)
  • Local Netmask: enter the local netmask (255.255.255.0 in this example)
  • Remote Subnet: enter the remote subnet (192.168.1.0 in this example)
  • Remote Netmask: enter the remote netmask(255.255.255.0 in this example)
  • Remote Gateway: enter the remote gateway
  • IKE Keep Alive(Ping IP Address): enter the default gateway of the remote location
  • Preshared Key: enter a key (The preshared key must be the same on both side.)

Click Apply.

A10505_image10

Step 6: Select Home, VPN, More and click on Select IKE Proposal.

A10505_image11

Step 7: Configure the IKE Proposal ID 1 as followed:

  • Proposal Name: enter a name as desired
  • DH Group: select Group 1
  • Encrypt algorithm: select 3DES
  • Auth algorithm: select SHA1
  • Life Time: select 28800
  • Life Time Unit: select Sec.
  • Proposal ID: use the dropdown list and select 1 and click Add to so that the name of the proposal appears in the IKE Proposal index.

Click Apply.

A10505_image12

Step 8: Select Home, VPN, More and click on Select IPSec Proposal.

A10505_image13

Step 9: Configure the IPSec Proposal ID 1 as followed:

  • Proposal Name: enter a name as desired
  • DH Group: select Group 1
  • Encap protocol: select ESP
  • Encrypt algorithm: select 3DES
  • Auth algorithm: select SHA1
  • Life Time: select 3600
  • Life Time Unit: select Sec.
  • Proposal ID: use the dropdown list and select 1 and click Add to so that the name of the proposal appears in the IPSec Proposal index.

Click Apply.

A10505_image14

Step 10: Select the Status tab and click on VPN Status. Click Refresh if the tunnel has not established.

A10505_image15

Tags: ,

Jun 19

Printers connected to the D-link DI-824VUP cannot be configured using the standard Windows TCP/IP port configuration wizard. You must install the PRTmate software that ships with the unit.

1.Software Installation

Step 1: Insert the installation CD into your CD-ROM drive.

If you have lost your installation CD, click here.

Step 2: Click Install D-Link Print Server Software.

Step 3: Select your operating system.

Step 4: Please wait while the InstallWizard® Wizard prepares the setup.

Step 5: Click Next.

Step 6: Click Browse if you wish to specify the folder to install the program. Click Next.

Step 7: Please wait while the print server software is installed.

Step 8: When setup is complete click Finish.

Step 9: Click OK and restart your computer.

2.Printer Configuration

Step 1: In Windows 2000 go to My Computer > Control Panel > Printers.

In Windows XP click Start > Control Panel > Printers and Faxes.

Step 2: Right-click the printer you want to configure and select Properties.

di-824VUP-1

Step 3: Click the Port tab, select PRT (Print Server), and then click Configure Port.

di-824VUP-2

Step 4: Select the interface (Parallel or USB) and then enter the IP address of the D-Link DI-824 below All-in-1 IP Sharer´s IP. Click OK.

di-824VUP-3

Step 5: Click OK.

di-824VUP-4

Tags: , ,

css.php