You will need the remote MAC address of the DWL-2200AP you are bridging to.
Step 1: Connect the DWL-2200AP to your PC using an Ethernet cable.
Step 2: Your computer will need to be in the same IP address range as the DWL-2100AP for configuration. The default IP address is 192.168.0.50.
Step 3: Open a web browser and enter in the IP address of the access point (http://192.168.0.50). The username is admin (all lower case) and the password is blank (nothing).
Step 4: Click on the Advanced tab and then click on Mode on the left side. At the top, click the PtP Bridge radio button. Enter the remote MAC address of the device you want to bridge to (IE 50:23:AB:D4:56:E1). Then click onApply to save your changes.
Step 5: Repeat the instructions for the remote access point. Click Apply to save your settings.
Note: If you have encryption enabled, ensure the key matches on both access points. Also, ensure that both access points do not have the same IP address. By default, the IP address is 192.168.0.50.
Tags: bridge mode, DWL-2200AP, Wireless ap
Step 1 Log into the web-based configuration by opening up a web browser and typing in the IP address of the access point (192.168.0.50).
Step 2 The default username is admin (all lower case) and the password is blank (nothing). Click OK.
Step 3 Click on the Advanced tab and then click Encryption on the left side. Select the Wireless Band (DWL-7100AP only).
Step 4 Click the radio button next to Shared Key and then click Enabled next to Encryption. Make sure your other wireless devices are set to Shared Key.
Step 5 Next to Key Type, select HEX or ASCII. You will need to use the same key on all your wireless devices.
- HEX – use 0-9 and A-F only.
- ASCII – All numbers and letters.Step 6 Next to Key Size, select the level of encryption (64, 128, or 152-bit).
Step 7 You can enter up to 4 different keys. Select the key you want to use from the Valid Key drop-down.
Step 8 Enter your encryption key. You make this up yourself. If you selected HEX, then enter a key made up of a combination of numbers (0-9) and letters (A-F). For example – A4572BCC19 (HEX).
Step 9 Click Apply to save settings.
Note: If you are configuring your access point from a wireless adapter, you will lose connectivity as soon as you click Apply. You must enable WEP on your adapter and enter the same exact key as you entered on your access point.
Tags: DWL-2100AP, DWL-2200AP, WEP Encryption
You can change the user name and password within the web-based configuration utility that is built-in to the access point.
Step 1: Open your web browser such as Internet Explorer. Enter the IP address of the D-Link access point (default is 192.168.0.50) and press Enter.
Step 2: Enter your username (admin) and your password (leave blank by default). Click OK.
Step 3: Click on the Tools tab at the top and then click Admin.
Step 4: Enter your new user name and then enter the old password (if any). Enter your new password and click Apply. After the access point restarts, you will be required to enter your new user name and password.
Tags: DWL-2100AP, DWL-2200AP, DWL-7100AP, password
Super G is Atheros’ proprietary frame-bursting, compression and channel bonding technology to improve IEEE 802.11g wireless LAN performance. The throughput transmission speed limit when using Super G is claimed to be up to 40Mbit/s-60Mbit/s at a 108Mbit/s signaling rate, which is achieved through the bonding of two 54Mbit/s 802.11g channels. Read More…
Step 1: Open your web browser and type the IP address of the D-Link DWL-7100AP access point in the address bar. The default IP address is 192.168.0.50. At the login, enter your username (admin) and password (default password is blank).
Step 2: Click on the Advanced tab and then click Performance on the left side.
Step 3: Next to Super Mode, select the mode you would like to use from the drop-down menu.
- Super G without Turbo
- Super G with Dynamic Turbo
- Super G with Static Turbo
Step 4: Click Apply and then click Continue to save your settings.
Tags: DWL-2100AP, DWL-2200AP, DWL-7100AP, Super G