Mar 18

Step 1: Open your web browser and log into your D-Link DSN series SAN ( the default IP address is http://192.168.1.1)

Step 2: Click on System Administration on the left hand side of the screen

Step 3: Click on the Control Tab

Step 4: Click on Restore Factory Defaults
A10107_image1

Tags: , ,

Nov 18

Note: This FAQ only applies to the D-Link DES-3226L Revision B.You can reset the unit to factory defaults using the following method:

DES-3226L_front

Facing the front of the switch, the Reset pin hole will be to the very right.

Using a paperclip, press and hold the Reset button for 10 seconds.

The D-Link DES-3226L should now be at factory defaults.

Tags: , ,

May 07

The D-Link DWL-G730AP is a very good travel wireless AP router, sometimes we forget the password, need to reset to factory settings, this article will tell you two ways.

1.Reset Button

If you have lost your password or are unable to login to the DWL-G730AP then it can be factory reset by doing the following:

Step 1: With the unit on, place a paper clip into the hole on the back on the unit labeled Reset.

Step 2: Hold paper clip down for 10 seconds and release.

How to perform a factory reset on D-Link DWL-G730AP Router

NOTE: DO NOT REPOWER UNIT DURING THIS PROCEDURE.

Step 3: The unit will reboot on its own. Once the WLAN light stops blinking, the unit is reset.

2.Web Configuration

If you are able to login to the D-Link DWL-G730AP then you can perform a factory reset via the web-based configuration by doing the following:

Step 1: Open a web browser and type the IP address of the DWL-G730AP in the address bar (default is 192.168.0.30). Press Enter.

Step 2: The default username is admin (all lower case) and the default password is blank (nothing). Click OK.

Step 3: Click the Tools tab and then click System to the left.

Step 4: Below Restore to Factory Default Settings click Restore.

Step 5: In the Restore to factory settings warning dialog box, click OK.

How to perform a factory reset on D-Link DWL-G730AP Router

NOTE: DO NOT REPOWER UNIT DURING THIS PROCEDURE.

How to perform a factory reset on D-Link DWL-G730AP Router

Step 6: The unit will reboot on its own. Once the WLAN light stops blinking, the unit is reset.

Note: Resetting the D-Link DWL-G730AP does not reset the firmware to an earlier version. It will change all settings back to factory defaults.

Tags: , , ,

Mar 01

Many friends asked that my D-Link DIR-655 forgot the password, how changed to manage? Here tell you how to reset it back to factory default settings.

Notes:D-Link dir-655 default does not have the password,you can enter the username admin and password is blank to try again.

Step 1: With the unit on, place a paper clip into the hole on the back on the unit labeled Reset.

Step 2: Hold paper clip down for 10 seconds and release.

Note: Do not repower unit during this procedure.

Step 3: The unit will reboot on its own. Once the WLAN light stops blinking, the unit is reset.

Resetting the router does not reset the firmware to an earlier version. It will change all settings back to factory defaults.

You can set an administrative password on DIR-655 router?

Step 1: Open a web browser and enter the IP address of the router in the address bar (default is 192.168.0.1). Press Enter.

Step 2: Click the Tools tab and then click Admin to the left.

dir-655-admin

Step 3: To change the administrative password, enter a new password in the Admin Password section.

Step 4: Click Save Settings to save the settings.

By the way:If you have the European version of this router, this procedure may not work. Please consult the D-Link office near you. D-Link USA does not support the European version.

Tags: , ,

Feb 17

Some people forget the D-Link DAP-1522 password,This article teaches how do reset on DAP-1522.

Step 1: With the unit on, place a paper clip into the hole on the back on the unit labeled Reset.

DAP-1522-3

Step 2: Hold paper clip down for 10 seconds and release.

Note: Do not repower unit during this procedure.

Step 3: The unit will reboot on its own. Once the WLAN light stops blinking, the unit is reset.

Resetting the D-Link DAP-1522 will change all settings back to factory defaults.

Note: The factory defaults name is admin, and password is blank(nothing).

Tags: , ,

css.php