D-Link Blog Home

The D-Link DWL-2700AP has been upgraded to the B version of the above changes：

Release Notes:

Firmware: 3.30
Date: 05/10/10

Problem Resolved:
1. [FW] Fix device with new flash cannot download image.
2. [FW] Disable the function that syslog file writing every five minutes, and remove syslog file parse when system initiates.
3. [FW] Remove the message ` Press Enter to login` when telnet.
4. Support Ethernet in/out traffic for standard MIB.
5. Support maximum community string length to 32 characters.

Enhancements:

1. [FW] add new Flash chip support.

Firmware: 3.20
Date: 12/21//09

1. Add Administration VLAN.
2. Add Primary SSID with VLAN tag.
3. Add Secondary Radius Server (backup).
4. Add Priority by SSID.
5. Add IGMP snooping v1/v2.
6. Add Rogue AP detection.
7. Support Acct-Interim-Interval attribute for accounting function.
8. Add trap categorization-trap enable/disable, system/wireless sub trap group.
9. Support Trap002-1.
10. Support to administrate AP with WLAN (Default enable).
11. Support 4 management IP range on WEB UI.
12, Add need CLI command to input SNMP Location.
14, Ping Enable/Disable (default: Ping Enable).
15. Add multi WMM control.

Firmware: 3.10
Date: 03/03/08

1. Fixed DHCP server malfunction in MSSID mode.
2. Fixed associated more than 83 STAs AP will reboot. Current limitation of allowed connected STAs is 64.
3. Modify HouseKeeping period from 60 seconds to 10 seconds.
4. If a specific STA be silent for 5 more seconds, AP could send a null-data to trigger it up.

Tags: DWL-2700AP, Firmware, vlan

My D-Link router DI-624 locked up,Follow these steps to solve the problem:

• A large amount of traffic may lock the router up. Disable any broadcast protocols or unused protocols such as NetBEUI and IPX/SPX.

• Disable UPnP(TM) if not being used on both your computer (ME or XP) and on the router (Tools – Misc).

• Check the log on your router. Is it showing a large amount of traffic? If coming from 1 IP address, you may want to use the IP Filter to block that user.

• Check the log settings and uncheck some of the items the router will report.

• Check your firewall and virtual server settings on the router. Too many may degrade performance of the router.

• Upgrade firmware. If you have the latest version, flash it again.

• Perform a hard reset on the router and reconfigure. With the unit powered on, use a paperclip and hold down the reset button for 10-15 seconds. Release and wait about 20 seconds. DO NOT power off while holding the reset button.

Tags: DI-624, Firmware, Locked up

D-Link DSR-500N Wireless Services Router Description:

Comprehensive Management Capabilities

The DSR-500N includes dual-WAN Gigabit Ethernet which provides policy-based service management ensuring maximum productivity for your business operations. The failover feature maintains data traffic without disconnecting when a landline connection is lost. The Outbound Load Balancing feature1 adjusts outgoing traffic across two WAN interfaces and optimizes the system performance resulting in high availability. The second WAN port can be configured as a DMZ port allowing you to isolate servers from your LAN.

Superior Wireless Performance

Designed to deliver superior wireless performance, the DSR-500N includes 802.11 b/g/n, allowing for operation on the 2.4 GHz radio band. Multiple In Multiple Out (MIMO) technology allows the DSR-500N to provide high data rates with minimal “dead spots” throughout the wireless coverage area.

Robust VPN Features

A fully featured virtual private network (VPN) provides your mobile workers and branch offices with a secure link to your network. The DSR-500N are capable of simultaneously managing 10 Secure Sockets Layer (SSL) VPN tunnels respectively, empowering your mobile users by providing remote access to a central corporate database. Site-to-site VPN tunnels use IP Security (IPSec) Protocol, Point-to-Point Tunneling Protocol (PPTP), or Layer 2 Tunneling Protocol (L2TP) to facilitate branch office connectivity through encrypted virtual links. The DSR-500N supports up to 35 simultaneous VPN tunnels.

·Integrated 802.11g/n wireless up to 300Mbps*
·4 Gigabit Ethernet ports
·Dual Gigabit WAN ports for Failover and Outbound Load-Balancing
·VPN Protocol Support for IPSec, PPTP, L2TP, and SSL
·Up to 35 VPN tunnels and Up to 10 SSL VPN tunnels
·Multiple 802.1q VLAN and SSID Support
·Static URL Address Filtering

D-Link DSR-500N Wireless Services Router Firmware:

Date: 12/28/2010

Version: 1.02

Download: ftp://ftp.dlink.com/Gateway/dsr500N/Firmware/dsr500N_FW_102.zip

Tags: DSR-500N, Firmware, Wireless

Step 1: Download the firmware and save the file to your computer. You may want to save the file to your desktop. Do not try to run or launch the file – it will not work.

WARNING: DO NOT upgrade the firmware with a wireless connection. You may damage the DWL-G730AP. Also, doing so could void the warranty.

Step 2: Open a web browser and type the IP address of the DWL-G730AP in the address bar (default is 192.168.0.30). Press Enter.

Step 3: The default username is admin (all lower case) and the default password is blank (nothing). Click OK.

Step 4: Click the Tools tab and then click Firmware to the left.

Step 5: Below Firmware Upgrade click Browse… and navigate to the .bin or .tfp file you downloaded in Step 1. Left-click the file once to select it and then click Open.

Step 6: Click Apply. It will take a few seconds for the upgrade to complete. Click Continue.

After the DWL-G730AP reboots, close your web browser and re-open it. Enter the IP address of the D-Link DWL-G730AP (default is 192.168.0.30) to reconnect to the web-based configuration. Enter username admin and again leave the password blank. Click OK.

Step 8: Click on the Tools tab then click Firmware to the left. If next to Current Firmware Version the new version is displayed then the firmware upgrade is now complete. If the firmware version has not changed then start over again from Step 2.

Step 9: If you have problems with the web-based configuration at this point, unplug the power to the DWL-G730AP, wait 10 seconds, and plug it back in. Repeat Step 7. If this did not help, perform a hard reset on the DWL-G730AP. To perform a hard reset, use a paperclip and hold down the reset button on the back of the unit for 10 seconds while the device is powered on. Release it and the DWL-G730AP will reboot, the lights will blink, and then stabilize. Repeat Step 7.

Step 10: You can now reconfigure the D-Link DWL-G730AP.

Check here you can see the DWL-G730AP User manaul.

Tags: DWL-G730AP, Firmware

The D-Link 4-Port Broadband Router been discontinued as of May 01, 2007 in the US.Many people are looking for DI-604 Firmware Download.

DI-604 Firmware Download:

site: ftp://ftp.dlink.com/Gateway/di604_revE1/Firmware/di604_revE_firmware_353.bin

Version:3.53

Date:4/24/2007

Revision Info:

¤ Updated DDNS screen and request.
¤ Updated PPPoE WAN settings.
¤ Applied minor Grammar corrections

1.How to upgrade the firmware on DI-604?

Step 1: Download the latest firmware.

Step 2: Once you´ve downloaded the firmware, open a web browser such as Internet Explorer or Netscape and enter the IP address of your router (192.168.0.1).

Step 3: Enter your username (admin) and your password (leave the field blank). Click OK to enter the web configuration for the device.

Step 4: Click on the Tools tab and then the Firmware button on the left side. Click on the Browse button and browse to the .bin (or .dlf) file you downloaded in Step 1. Highlight the file by clicking on it once and click Open.

Step 5: Click Apply. It may take a up to 30 seconds for the upgrade to complete. Click on the Continue button. The firmware is now upgraded.

Step 6: If you get a Page cannot be displayed or similar error after clicking Continue, close your browser and re-open it. Enter 192.168.0.1 and press Enter. You should now be prompted for your username (admin) and your password (leave blank).

2.How to upgrade the firmware on the D-Link DI-604 and the DI-614+ using a Macintosh computer?

Step 1. Create a Folder on the Desktop Screen:
From a blank spot the Desktop Screen, press and hold the Control key on the keyboard and click the mouse button. Release the Control key, click New Folder, and name it firmware.

Step 2. Retrieve Firmware from Website:
Click link below and download file to the folder created in step 1.

Step 3. Upgrade the Firmware:
A. From the Main Desktop Screen, launch Internet Explorer or Netscape.

B. Type 192.168.0.1 in the Address bar and click Go.

C. For the User ID, type admin and click OK.

D. Click Tools on the top and then click Firmware on the left side.

E. Click Browse>Desktop>firmware, double click di6xx_firmware_203.bin and click Apply. Wait for approx. 15 seconds or until the M2 light stops flashing on the DI-6xx unit then click Continue.

F. This takes you back to the Tools page. Check the Current Firmware Version on the Tools page to confirm that the firmware loaded successfully.

Tags: DI-604, Firmware, upgrade Firmware