Nov 11

Note: These FAQs were created for firmware version 2.05 and above.

Note: You need to disable any pop-up blockers on your computer.


Connect using DHCP

Step 1: Open a web browser and type the IP address of the DFL in the address bar (default is 192.168.1.1) and press Enter.

Step 2: Enter username and password. Default username and password is admin.

A10186_image1

Step 3: The web GUI will begin with the D-Link setup wizard, or select the Setup Wizard button (available in firmware 2.26 or higher). Click Next.

A10186_image2

Step 4: You can set a new password here by entering the new password and re-typing the password to confirm then click Next.

A10186_image3

Step 5: Select the appropriate time zone then click Next.

A10186_image4

Step 6: Select WAN1 in the dropdown then click Next.

A10186_image5

Step 7: Select DHCP-automatic configuration then click Next.

A10186_image6

Step 8: Select Enable DHCP Servers (Optional) and configure as followed:

  • IP range: enter desired range IP for DHCP clients
  • Subnet Mask: entered corresponding subnet mask
  • Default Gateway: enter LAN IP of the firewall
  • DNS Server: enter desired DNS IP address

Click Next.

A10186_image7

Step 9: Configure the NTP Server as desired (Optional) then click Next.

A10186_image8

Step 10: Click Activate to save the configuration.


Connect using PPPoE

Step 1: Open a web browser and type the IP address of the DFL in the address bar (default is 192.168.1.1) and press Enter.

Step 2: Enter username and password. Default username and password is admin.

A10186_image9

Step 3: The web GUI will begin with the D-Link setup wizard, or select the Setup Wizard button (available in firmware 2.26 or higher). Click Next.

A10186_image10

Step 4: You can set a new password here by entering the new password and re-typing the password to confirm then click Next.

A10186_image11

Step 5: Select the appropriate time zone then click Next.

A10186_image12

Step 6: Select WAN1 in the dropdown then click Next.

A10186_image13

Step 7: Select the radio button labeled PPPoE-account details needed then click Next.

A10186_image14

Step 8: Enter your DSL account details provided by your ISP then click Next.

A10186_image15

Step 9: Select Enable DHCP Servers (Optional).

  • IP range: enter desired range IP for DHCP clients
  • Subnet Mask: entered corresponding subnet mask
  • Default Gateway: enter LAN IP of the firewall
  • DNS Server: enter desired DNS IP address

Click Next.

A10186_image16

Step 10: Configure the NTP Server as desired (Optional) then click Next.

A10186_image17

Step 11:: Click activate to save the configuration.

A10186_image18

Step 12: Click Close after the firewall is done saving the configuration.


Connect using a Static IP

Step 1: Open a web browser and type the IP address of the DFL in the address bar (default is 192.168.1.1) and press Enter.

Step 2: Enter username and password. Default username and password is admin.

A10186_image19

Step 3: The web GUI will begin with the D-Link setup wizard, or select the Setup Wizard button (available in firmware 2.26 or higher). Click Next.

A10186_image20

Step 4: You can set a new password here by entering the new password and re-typing the password to confirm then click Next.

A10186_image21

Step 5: Select the appropriate time zone then click Next.

A10186_image22

Step 6: Select WAN1 in the drop-down then click Next.

A10186_image23

Step 7: Select Static-manual configuration then click Next.

A10186_image24

Step 8: Configure the WAN1 for static public IP address as followed:

  • IP address: enter public IP address provided by ISP
  • NetMask: enter appropriated subnet mask provided by ISP
  • Gateway: enter gateway IP address provided by ISP
  • Primary DNS: enter DNS IP address provided by ISP
  • Secondary DNS: enter DNS IP address provided by ISP

Click Next.

A10186_image25

Step 9: Select enable DHCP Servers (Optional).

  • IP range: enter desired range IP for DHCP clients
  • Subnet Mask: entered corresponding subnet mask
  • Default gateway: enter LAN IP of the firewall
  • DNS Server: enter desired DNS IP address

Click Next.

A10186_image26

Step 10: Configure the NTP Server as desired (Optional) then click Next.

A10186_image27

Step 11: Click Activate to save the configuration.

A10186_image28

Step 12: Click Close after the firewall is done saving the configuration.

Tags: , , ,

css.php