Nov 11

Note: These FAQs were created for firmware version 2.05 and above.

Note: You need to disable any pop-up blockers on your computer.


Connect using DHCP

Step 1: Open a web browser and type the IP address of the DFL in the address bar (default is 192.168.1.1) and press Enter.

Step 2: Enter username and password. Default username and password is admin.

A10186_image1

Step 3: The web GUI will begin with the D-Link setup wizard, or select the Setup Wizard button (available in firmware 2.26 or higher). Click Next.

A10186_image2

Step 4: You can set a new password here by entering the new password and re-typing the password to confirm then click Next.

A10186_image3

Step 5: Select the appropriate time zone then click Next.

A10186_image4

Step 6: Select WAN1 in the dropdown then click Next.

A10186_image5

Step 7: Select DHCP-automatic configuration then click Next.

A10186_image6

Step 8: Select Enable DHCP Servers (Optional) and configure as followed:

  • IP range: enter desired range IP for DHCP clients
  • Subnet Mask: entered corresponding subnet mask
  • Default Gateway: enter LAN IP of the firewall
  • DNS Server: enter desired DNS IP address

Click Next.

A10186_image7

Step 9: Configure the NTP Server as desired (Optional) then click Next.

A10186_image8

Step 10: Click Activate to save the configuration.


Connect using PPPoE

Step 1: Open a web browser and type the IP address of the DFL in the address bar (default is 192.168.1.1) and press Enter.

Step 2: Enter username and password. Default username and password is admin.

A10186_image9

Step 3: The web GUI will begin with the D-Link setup wizard, or select the Setup Wizard button (available in firmware 2.26 or higher). Click Next.

A10186_image10

Step 4: You can set a new password here by entering the new password and re-typing the password to confirm then click Next.

A10186_image11

Step 5: Select the appropriate time zone then click Next.

A10186_image12

Step 6: Select WAN1 in the dropdown then click Next.

A10186_image13

Step 7: Select the radio button labeled PPPoE-account details needed then click Next.

A10186_image14

Step 8: Enter your DSL account details provided by your ISP then click Next.

A10186_image15

Step 9: Select Enable DHCP Servers (Optional).

  • IP range: enter desired range IP for DHCP clients
  • Subnet Mask: entered corresponding subnet mask
  • Default Gateway: enter LAN IP of the firewall
  • DNS Server: enter desired DNS IP address

Click Next.

A10186_image16

Step 10: Configure the NTP Server as desired (Optional) then click Next.

A10186_image17

Step 11:: Click activate to save the configuration.

A10186_image18

Step 12: Click Close after the firewall is done saving the configuration.


Connect using a Static IP

Step 1: Open a web browser and type the IP address of the DFL in the address bar (default is 192.168.1.1) and press Enter.

Step 2: Enter username and password. Default username and password is admin.

A10186_image19

Step 3: The web GUI will begin with the D-Link setup wizard, or select the Setup Wizard button (available in firmware 2.26 or higher). Click Next.

A10186_image20

Step 4: You can set a new password here by entering the new password and re-typing the password to confirm then click Next.

A10186_image21

Step 5: Select the appropriate time zone then click Next.

A10186_image22

Step 6: Select WAN1 in the drop-down then click Next.

A10186_image23

Step 7: Select Static-manual configuration then click Next.

A10186_image24

Step 8: Configure the WAN1 for static public IP address as followed:

  • IP address: enter public IP address provided by ISP
  • NetMask: enter appropriated subnet mask provided by ISP
  • Gateway: enter gateway IP address provided by ISP
  • Primary DNS: enter DNS IP address provided by ISP
  • Secondary DNS: enter DNS IP address provided by ISP

Click Next.

A10186_image25

Step 9: Select enable DHCP Servers (Optional).

  • IP range: enter desired range IP for DHCP clients
  • Subnet Mask: entered corresponding subnet mask
  • Default gateway: enter LAN IP of the firewall
  • DNS Server: enter desired DNS IP address

Click Next.

A10186_image26

Step 10: Configure the NTP Server as desired (Optional) then click Next.

A10186_image27

Step 11: Click Activate to save the configuration.

A10186_image28

Step 12: Click Close after the firewall is done saving the configuration.

Tags: , , ,

Aug 16

The WAN settings can be configured on the DWL-G730AP in Router Mode.

Step 1: Open a web browser and type the IP address of the D-Link DWL-G730AP in the address bar (default is 192.168.0.30). Press Enter.

Step 2: The default username is admin (all lower case) and the default password is blank (nothing). Click OK.

Step 3: Click the Home tab and then click WAN to the left.

Step 4: Choose one of the following connection types using the radio buttons:

1.Dynamic IP Address – Obtain an IP address automatically.

dwl-g730ap-wan1

2.Static IP Address – If your ISP provided you with a static IP address choose this option.

dwl-g730ap-wan2

3.PPPoE (Point to Point Protocol over Ethernet) – Most commonly used by DSL providers.

dwl-g730ap-wan3

Other > PPTP – European use only.

Other > BigPond Cable – Australia use only.

dwl-g730ap-wan4

Host Name – The Host Name is optional but may be required by some ISPs. The default host name is the device name of the router and may be changed.

MAC Address – The default MAC address is set to the WAN´s physical interface MAC address on the router. It is not recommended that you change the default MAC address unless required by your ISP.

Clone MAC Address – The default MAC address is set to the WAN´s physical interface MAC address on the router. You can use the Clone MAC Address button to copy the MAC address of the Ethernet card on your computer and replace the WAN MAC address with the MAC address of your computer. It is not recommended that you change the default MAC address unless required by your ISP.

Primary/Secondary DNS Address – Enter the primary DNS address. The secondary DNS address is optional.

MTU (Maximum Transmission Unit) – 1500 is the default MTU. Enter a new MTU value only if required by your ISP. Otherwise, do not change this setting.

Step 5: Click Apply then click Continue to save the new settings.

Read More: How to configure the wireless settings on D-Link DWL-G730AP?

D-Link DWL-G730AP Manual,Wireless Pocket Router/AP user manual

Tags: , ,

css.php