Jan 05

You may log into the web-based configuration utility on the D-Link DAP-1520 to perform the following tasks:

• Run the Setup Wizard

• Upgrade firmware

• Change wireless and network settings

1. Plug the DAP-1520 into an available outlet near your router. You may move it to a more suitable location after configuration.

A10716_image1

2. Open the wireless utility on your wireless device or computer. Select the Wi-Fi Network Name (from the Wi-Fi Configuration Card) and enter the Password.

A10716_image2

3. Open a web browser (e.g., Internet Explorer, Firefox, Safari, or Chrome) and enter http://dlinkap.local./.You may also enter the IP address* of the DAP-1520. Windows XP users can enter http://dlinkap.

A10716_image3
4. Once you connect, the login page will appear. Enter your password and click Log In. By default the password is blank.
Note: If this is the first time logging in to the DAP-1520, you will be directed to the Setup Wizard automatically.
A10716_image4
* The default IP address is 192.168.0.50. Once the DAP-1520 connects to your router, it will get assigned a new IP address based on your router/network’s DHCP settings. You will need to log in to your router and view the DHCP table to see what IP address was assigned to the DAP-1520. The MAC address is printed on the label on the DAP-1520.
5. The home page will display your current status. A green check mark represents a successful connection to your wireless router or Access Point (AP).
A10716_image5
If the check mark is red, you may connect to your wireless router or AP by clicking on the Uplink Router icon.

Tags: , ,

Jan 16

Connecting to the AP Web Interface by Using the IPv6 Address

To connect to the AP by using the IPv6 global address or IPv6 link local address, you must enter the AP address into
your browser in a special format.

Note: The following instructions and examples work with Microsoft Internet Explorer 7 (IE7) and might not work with other browsers.

To connect to an IPv6 global address, add square brackets around the IPv6 address. For example, if the AP global IPv6 address is 2520::230:abff:fe00:2420, type the following address into the IE7 address field: http://[2520::230:abff:fe00:2420].

To connect to the iPv6 link local address, replace the colons (:) with hyphens (-), add the interface number preceded with an “s,” then add “.ipv6-literal.net.” For example, if the AP link local address is fe80::230:abff:fe00:2420, and the Windows interface is defined as “%6,” type the following address into the IE7 address field: http://fe80–230-abff-fe00-2420s6.ipv6-literal.net.

How to using the CLI to View the IP Address On D-Link DWL-2600AP Access Point

The DHCP client on the UAP is enabled by default. If you connect the UAP to a network with a DHCP server, the AP automatically acquires an IP address. To manage the UAP by using the Administrator UI, you must enter the IP address of the access point into a Web browser.

If a DHCP server on your network assigns an IP address to the UAP, and you do not know the IP address, use the following steps to view the IP address of the UAP:

1.) Using a null-modem cable, connect a VT100/ANSI terminal or a workstation to the console (serial) port.
If you attached a PC, Apple, or UNIX workstation, start a terminal-emulation program, such as HyperTerminal or
TeraTerm.

2.) Configure the terminal-emulation program to use the following settings:
•) Baud rate: 115200 bps
•) Data bits: 8
•) Parity: none
•) Stop bit: 1
•) Flow control: none

D-Link-DWL-2600AP-IPv6-Address

3.) Press the return key, and a login prompt should appear.The login name is admin. The default password is admin. After a successful login, the screen shows the(Access Point Name)# prompt.

4.) At the login prompt, enter get management.Information similar to the following prints to the screen.

Configuring the Ethernet Settings On D-Link DWL-2600AP

The default Ethernet settings, which include DHCP and VLAN information, might not work for all networks.By default, the DHCP client on the UAP automatically broadcasts requests for network information. If you want to use a static IP address, you must disable the DHCP client and manually configure the IP address and other network information.

The management VLAN is VLAN 1 by default. This VLAN is also the default untagged VLAN. If you already have a management VLAN configured on your network with a different VLAN ID, you must change the VLAN ID of the management VLAN on the access point.

Tags: , ,

Nov 19

1.Plug the DAP-1320 into a wall outlet and verify if the power LED has turned from red to a blinking amber.D-Link-DAP-1320-Wi-Fi-Range-Extender-Web-Browser-Setup1

2.From your laptop or mobile device go to your Wireless Utility to display the available wireless networks and select the Wi-Fi Network Name (SSID) that is located on your configuration note (ex: dlink-a8fa). Then, enter the Wi-Fi password which is also located on your configuration note. (ex: akbdj19368).

D-Link-DAP-1320-Wi-Fi-Range-Extender-Web-Browser-Setup2

3.Open a web browser and type http://dlinkap.local (Windows/Mac/iPhone/iPad). Please follow the on-screen instructions to complete the setup.

D-Link-DAP-1320-Wi-Fi-Range-Extender-Web-Browser-Setup3

4.Select the configuration method and click Next.For Manual configuration, select the Wi-Fi network you would like the D-Link DAP-1320 to connect to wirelessly.

D-Link-DAP-1320-Wi-Fi-Range-Extender-Web-Browser-Setup4

5.Enter the Wi-Fi Password for the router you are using to connect and click Next.Once the second screen appears, you can choose to change the Wi-Fi Network Name (SSID) and the Wi-Fi Password for the DAP-1320. Click Next to continue and finish the setup process.

D-Link-DAP-1320-Wi-Fi-Range-Extender-Web-Browser-Setup5

6.From your laptop or mobile device go to your wireless utility to display the available wireless networks. Then, search for the Wi-Fi Network Name (SSID) for the DAP-1320 that you created in Step 5 and connect to the network.

D-Link-DAP-1320-Wi-Fi-Range-Extender-Web-Browser-Setup6

Tags: , ,

css.php