May 21

Package Contents

Open the shipping carton of the Switch and carefully unpack its contents. The carton should contain the following items:

1. One Switch
2. One AC power cord
3. Mounting kit (two brackets and screws)
4. Four rubber feet with adhesive backing
5. RS-232 console cable
6. One CD Kit for DWS-3000 Series Administrator’s Guide and CLI Reference Guide
7. Registration card & China Warranty Card (for China only)

If any item is missing or damaged, please contact your local D-Link Reseller for replacement.

Installation Guidelines

Please follow these guidelines for setting up the Switch:

• Install the Switch on a sturdy, level surface that can support at least 6.6 lb. (3 kg) of weight. Do not place heavy objects on the Switch.

• The power outlet should be within 1.82 meters (6 feet) of the Switch.

• Visually inspect the power cord and see that it is fully secured to the AC power port.

• Make sure that there is proper heat dissipation from the Switch and adequate ventilation around the Switch. Leave at least 10 cm (4 inches) of space at the front and rear of the Switch for ventilation.

• Install the Switch in a fairly cool and dry place for the acceptable temperature and humidity operating ranges.

• Install the Switch in a site free from strong electromagnetic field generators (such as motors), vibration, dust, and direct exposure to sunlight.

• When installing the Switch on a level surface, attach the rubber feet to the bottom of the device. The rubber feet cushion the Switch, protect the casing from scratches, and prevent it from scratching other surfaces.

Installing the Switch without the Rack

First, attach the rubber feet included with the Switch if installing on a desktop or shelf. Attach these cushioning feet on the bottom at each corner of the device. Allow enough ventilation space between the Switch and any other objects in the vicinity.

DWS-3026-Installation1

Installing the Switch in a Rack

The Switch can be mounted in a standard 19″ rack. Use the following diagrams as a guide.

DWS-3026-Installation2

Fasten the mounting brackets to the Switch using the screws provided.

Powering On the Switch

Plug one end of the AC power cord into the power connector of the Switch and the other end into the local power source outlet.

After powering on the Switch, the LED indicators will momentarily blink. This blinking of the LED indicators represents a reset of the system.

Power Failure

As a precaution, in the event of a power failure, unplug the Switch. When power is resumed, plug the Switch back in.

Installing the SFP ports

DWS-3026-Installation3

The D-Link DWS-3000 series switches are equipped with SFP (Small Form-factor Pluggable) ports,which are to be used with fiber-optical transceiver cabling in order to uplink various other networking devices for a gigabit link that may span great distances. These SFP ports support full-duplex transmissions, have auto-negotiation and can be used with DEM-310GT (1000BASE-LX), DEM-311GT (1000BASE-SX), DEM-314GT (1000BASE-LH) and DEM-315GT (1000BASE-ZX) transceivers. See the figure below for installing the SFP ports in the Switch.

Installing the Optional Modules

The rear panel of the D-Link DWS-3026 includes two open slots that may be equipped with the DEM-410X 1-port 10GE XFP uplink module, or a DEM-410CX 1-port 10GBASE-CX4 uplink module, both sold separately.

Adding the DEM-410X optional module allows the switch to transmit data at a rate of ten gigabits per second. The module port(s) are compliant with standard IEEE 802.3ae, support full-duplex transmissions only and must be used with XFP MSA-compliant transceivers.

The DEM-410CX uses copper wire medium, not optic fiber and therefore has a transmit length limit up to 1 meters. Compliant with the IEEE802.3ak standard, this module uses a 4-lane copper connector for data transfer in full-duplex mode.

To install these modules in the D-Link DWS-3026 Switch, follow the steps listed in this section.

CAUTION: Before adding the optional module, make sure to disconnect all power sources connected to the Switch. Failure to do so may result in an electrical shock, which may cause damage, not only to the individual but to the Switch as well.

At the back of the Switch to the left are the two slots for the optional modules. These slots must be covered with the faceplate if the slots are not being used. To install a module in an available slot, remove the faceplate by loosening the screws and pulling off the plate.

Install the Module

Unplug the Switch before removing the faceplate covering the empty slot. To install the module, slide it in to the available slot at the rear of the Switch until it reaches the back, as shown in the following figure. Gently, but firmly push in on the module to secure it to the Switch. The module should fit snugly into the corresponding receptors.

DWS-3026-Installation4

Now tighten the two screws at adjacent ends of the module into the available screw holes on the Switch. The upgraded Switch is now ready for use.

Connecting to the External Redundant Power System

The Switch supports an external redundant power system (RPS). The diagrams below illustrate a proper RPS power connection to the Switch. Please consult the documentation for information on power cabling and connectors and setup procedure.

DWS-3026-Installation5

Tags: , ,

Apr 10

1.What do I need to use my Access Points with D-Link wireless switch.

Step 1:

 1a): A DHCP Server is required to be on the same Interface as the switch.
1b): A DHCP Server is required for the Access Points to be discovered by
the switch.

Step 2: This line of switches utilizes Proprietary Access Points.

The DWL-7130AP and the DWL-7230AP and the DWL-2230AP as well as the DWL-2130AP´s

Step 3: The DXS line of switches also requires an additional Wireless license provided from our DLink Sales Department.

dlink-dws3227

2.How many Access Points can be configured per D-Link switch?

You can only configure 10 Access Points per switch.

The DWS-3227/3227P/3250 comes with a 10 Access Point license.

The DXS-3227/3227P/3250 requires the purchase of additional software to enable the wireless feature. Once enabled, the switch will support 10 Access Point (10 Access Point license included).

3.What is the maximum number of Access Points can I configure per D-Link switch?

You can configure a maximum of 50 access points per switch (with appropriate licenses), with Firmware version 1.0.1.109 or above.

Note: If you have multiple switches in Stack Mode, the stack acts as one physical switch and will only support 10 Access Points. To add more Access Points, additional Licenses will be required (additional licenses sold seperately).

You are also able to configure a maximum of 50 Access Points in Stack Mode.

Your slave/backup switch will also require another License key to manage your access points if your master goes down.

D-Link offers 25 and 50 User Licenses (sold seperately).

Tags: ,

Jan 31

Bandwidth Control Increments: 10/100Mbps port = 1-100 in multiples of 1, 10/100/1000Mbps port = 8-1000 in multiples of 8. The D-Link switches that support Bandwidth Control are listed below. Click on the model number of the switch for configuration instructions.

D-Link DES Series switch:

•DES-3028
•DES-3028P
•DES-3052
•DES-3052P
•DES-3226
•DES-3226L
•DES-3226SM
•DES-3326SRM
•DES-3250TG
•DES-3350SR
•DES-3526
•DES-3528
•DES-3550
•DES-3828
•DES-3828P
•DES-3852

D-Link DGS Series switch:

•DGS-3100-24
•DGS-3100-24P
•DGS-3100-48
•DGS-3100-48P
•DGS-3200-10
•DGS-3200-24
•DGS-3224TGR
•DGS-3224SR
•DGS-3324SR
•DGS-3324SRi
•DGS-3212SR
•DGS-3426
•DGS-3426P
•DGS-3427
•DGS-3450
•DGS-3612G
•DGS-3627
•DGS-3627G
•DGS-3650

D-Link DWS Wireless Switch Series:

•DWS-3024L
•DWS-3026
•DWS-4026

——————————————————————————–

Tags: ,

Jul 30

Step 1: Save all your changes and reload the switch.

Step 2: When you see the Auto boot in 2 seconds message, press Return or Esc to abort the boot process and enter prom.

Here you will see the following options:

Startup Menu

[1] Download Software
[2] Erase Flash File
[3] Password Recovery Procedure
[4] Enter Diagnostic Mode
[5] Set Terminal Baud-Rate
[6] Stack menu
[7] License menu
[8] Back

Step 3: Select option # 7, License menu, and press Enter

Here you will see the following options:

License menu

[1] Add license
[2] Remove license
[3] Show license
[4] Back

Step 4: Select option # 1, Add license, and press Enter.

Step 5: Enter your license number and press Enter.

The License number will be in the following format:
N1-0013463CBACB-25-0-79109C235845B9A5 (This is an sample. it is not a working key)
Key starts with N1 (all letters are capitalized).

Step 6: After adding the key, select option #3, Show License, to confirm the key is entered correctly.

Step 7: Select the back option until the POST process resumes.

Now you are able to access the WLAN portion of the switch.

Tags: , ,

Feb 07

1 Q:Which wireless access points are compatible with both the DXS/DWS-3227 and the DXS/DWS-3227P wireless switches?

The following access points are compatible with the DXS/DWS-3227 as well as the DXS/DWS-3227P wireless switches:

* DWL-2130AP
* DWL-2230AP
* DWL-7130AP
* DWL-7230AP
* DWL-3230AP

2 Q:What do I need to use my Access Points with my wireless switch?

Step 1: A DHCP Server is required to be on the same Interface as the switch.
A DHCP Server is required for the Access Points to be discovered by
the switch.

Step 2: This line of switches utilizes Proprietary Access Points.

The DWL-7130AP and the DWL-7230AP and the DWL-2230AP as well as the DWL-2130AP´s

Step 3: The DXS line of switches also requires an additional Wireless license
provided from our DLink Sales Department.

3 Q:How many Access Points can be configured per switch?

You can only configure 10 Access Points per switch.

The DWS-3227/3227P/3250 comes with a 10 Access Point license.

The DXS-3227/3227P/3250 requires the purchase of additional software to enable the wireless feature. Once enabled, the switch will support 10 Access Point (10 Access Point license included).

4 Q:What is the maximum number of Access Points can I configure per switch?

You can configure a maximum of 50 access points per switch (with appropriate licenses), with Firmware version 1.0.1.109 or above.

Note: If you have multiple switches in Stack Mode, the stack acts as one physical switch and will only support 10 Access Points. To add more Access Points, additional Licenses will be required (additional licenses sold seperately).

You are also able to configure a maximum of 50 Access Points in Stack Mode.

Your slave/backup switch will also require another License key to manage your access points if your master goes down.

D-Link offers 25 and 50 User Licenses (sold seperately).

Tags: ,



 
Prev 1 2
css.php